|
|
|
题名
|
作者
|
年代
|
出处
|
被引量
|
| 1 | Anti-loosening performance of coatings on fasteners subjected to dynamic shear load显示文摘This paper investigates the self-loosening of threaded fasteners subjected to dynamic shear load. Three kinds of typical coatings, PTFE, MoS_2, and TiN applied to bolts and nuts, are tested in this investigation. The study experimentally examines the loosening mechanisms of fasteners and assesses the anti-loosening performance of the three tested coatings based on their tightening characteristics, loosening curves, and the damage of thread surface. Additionally, the anti-loosening performance of the three coatings is compared under different load forms. The results indicate that the PTFE and MoS_2 coatings have significant anti-loosening effect, whereas the anti-loosening performance of Ti N coating is not satisfactory. It is also found that an appropriate increase of the initial tightening torque can significantly improve the anti-loosening effect. In addition, the microscopic analyses of PTFE and MoS2 coating reveal that a reduced initial tightening torque leads to fretting wear on the thread contact surfaces of fasteners, thereby aggravating the damage. | Junbo ZHOU Jianhua LIU Huajiang OUYANG Zhenbing CAI Jinfang PENG Minhao ZHU | 2018 | Friction2018，6，1： | 10 |
| 2 | Fermentation characteristics and probiotic activity of a purified fraction of polysaccharides from Fuzhuan brick tea显示文摘Polysaccharides from Fuzhuan brick tea(FBTPS),one of most important bioactive components in tea,showed various health-promoting functions.Our previous work demonstrated that the crude FBTPS(CFBTPS)could modulate the gut microbiota.However,which purified fraction in CFBTPS contributing to the modulation of gut microbiota remains unclear.Thus,the fermentation characteristics and probiotic activity of a purified fraction(FBTPS-2-1)of CFBTPS were evaluated in this work.The results showed that gut microbiota could utilize FBTPS-2-1 to produce short-chain fatty acids including acetic,propionic,n-butyric and n-valeric acids.FBTPS-2-1 could modulate the structure and metabolic pathways of gut microbiota.FBTPS-2-1 could increase the health-promoting gut microbiota such as Prevotellaceae and Bifidobacteriaceae,and decreased the harmful bacteria such as Enterobacteriaceae and Fusobacteriaceae.The results of metagenomics showed that Prevotella copri and Megamonas funiformis were the dominant bacteria after fermentation of FBTPS-2-1.Furthermore,FBTPS-2-1 could regulate the biosynthesis and metabolism pathways of gut microbiota.Thus,the enrichment of food with FBTPS-2-1 is expected as a potential strategy for promoting human health due to modulation of gut microbiota. | Guijie Chen Ziqi Zeng Minhao Xie Yujia Peng Wangting Zhou Weiqi Xu Yi Sun Xiaoxiong Zeng Zhonghua Liu | 2022 | Food Science and Human Wellness2022，11，3： | 4 |
| 3 | Fretting Wear Behavior of Medium Carbon Steel Modified by Low Temperature Gas Multi-component Thermo-chemical Treatment显示文摘The introduction of surface engineering is expected to be an effective strategy against fretting damage. A large number of studies show that the low gas multi-component (such as carbon, nitrogen, sulphur and oxygen, etc) thermo-chemical treatment(LTGMTT) can overcome the brittleness of nitriding process, and upgrade the surface hardness and improve the wear resistance and fatigue properties of the work-pieces significantly. However, there are few reports on the anti-fretting properties of the LTGMTT modified layer up to now, which limits the applications of fretting. So this paper discusses the fretting wear behavior of modified layer on the surface of LZ50 (0.48%C) steel prepared by low temperature gas multi-component thermo-chemical treatment (LTGMTT) technology. The fretting wear tests of the modified layer flat specimens and its substrate (LZ50 steel) against 52100 steel balls with diameter of 40 mm are carried out under normal load of 150 N and displacement amplitudes varied from 2 μm to 40 μm. Characterization of the modified layer and dynamic analyses in combination with microscopic examinations were performed through the means of scanning electron microscope(SEM), optical microscope(OM), X-ray diffraction(XRD) and surface profilometer. The experimental results showed that the modified layer with a total thickness of 60 μm was consisted of three parts, i.e., loose layer, compound layer and diffusion layer. Compared with the substrate, the range of the mixed fretting regime(MFR) of the LTGMTT modified layer diminished, and the slip regime(SR) of the modified layer shifted to the direction of smaller displacement amplitude. The coefficient of friction(COF) of the modified layer was lower than that of the substrate in the initial stage. For the modified layer, the damage in partial slip regime(PSR) was very slight. The fretting wear mechanism of the modified layer both in MFR and SR was abrasive wear and delamination. The modified layer presented better wear resistance than the substrate in PSR and MFR; however, in SR, the wear resistance of the modified layer decreased with the increase of the displacement amplitudes. The experimental results can provide some experimental bases for promoting industrial application of LTGMTT modified layer in anti-fretting wear. | LUO Jun ZHENG Jianfeng PENG Jinfang HE Liping ZHU Minhao | 2010 | Chinese Journal of Mechanical Engineering2010，23，3： | 3 |
| 4 | Development of a novel cycling impact–sliding wear rig to investigate the complex friction motion显示文摘In many industrial devices, impact-sliding wear is caused by a variety of complex vibrations between the contacted interfaces. Under actual conditions, impact and sliding motions do not occur in only one direction, and different complex impact-sliding motions exist on the tribology surfaces. In this study, an impact-sliding wear test rig is developed to investigate the wear effect of different complex motions. Using this rig, multi-type impact-sliding wear effects are realized and measured, such as those derived from unidirectional, reciprocating, and multi-mode combination motions. These three types of impact–sliding wear running behavior are tested and the wear damage mechanism is discussed. | Zhenbing CAI Zhiqiang CHEN Yang SUN Jianying JIN Jinfang PENG Minhao ZHU | 2019 | Friction2019，7，1： | 2 |
| 5 | The C_(6)D_(6)detector system on the Back-n beam line of CSNS显示文摘Introduction The neutron capture cross sections are very important in the field of nuclear device design and basic physics research.Hydrogen-free liquid scintillator such as C_(6)D_(6)detectors are widely used in the neutron capture cross-sectional measurements for the low neutron sensitivity and fast time response.The Back-n white neutron source at China Spallation Neutron Source is the first spallation white neutron source in China,and it is suitable for neutron capture cross-sectional measurement.Materials and methods A C_(6)D_(6)detector system was built in the Back-n experimental station.The pulse height weighting technique was used to determine the system’s detection efficiency.The response to gamma rays of the C_(6)D_(6)detector was measured,and the energy resolution function was determined.Monte Carlo simulation with Geant4 code was carried out to get the weighting function of this C_(6)D_(6)detector system.Additionally,the systematic uncertainty of the weighting function was also determined.Conclusion According to the experimental and simulation results,this C_(6)D_(6)detector system can be used to measure neutron capture cross section. | Jie Ren Xichao Ruan Jie Bao Guangyuan Luan Wei Jiang Qi An Huaiyong Bai Ping Cao Qiping Chen Yonghao Chen Pinjing Cheng Zengqi Cui Ruirui Fan Changqing Feng Minhao Gu Fengqin Guo Changcai Han Zijie Han Guozhu He Yongcheng He Yuefeng He Hanxiong Huang Weiling Huang Xiru Huang Xiaolu Ji Xuyang Ji Haoyu Jiang Hantao Jing Ling Kang Mingtao Kang Bo Li Lun Li Qiang Li Xiao Li Yang Li Yang Li Rong Liu Shubin Liu Xingyan Liu Yinglin Ma Changjun Ning Binbin Qi Zhaohui Song Hong Sun Xiaoyang Sun Zhijia Sun Zhixin Tan Hongqing Tang Jingyu Tang Pengcheng Wang Qi Wang Taofeng Wang Yanfeng Wang Zhaohui Wang Zheng Wang Jie Wen Zhongwei Wen Qingbiao Wu Xiaoguang Wu Xuan Wu Likun Xie Yiwei Yang Han Yi Li Yu Tao Yu Yongji Yu Guohui Zhang Jing Zhang Linhao Zhang Liying Zhang Qingmin Zhang Qiwei Zhang Xianpeng Zhang Yuliang Zhang Zhiyong Zhang Yingtan Zhao Liang Zhou Zuying Zhou Danyang Zhu Kejun Zhu Peng Zhu | 2019 | Radiation Detection Technology and Methods2019，3，3： | 1 |
| 6 | Hierarchical Ti_(3)C_(2)T_(x)@MoS_(2) heterostructures:A first principles calculation and application in corrosion/wear protection显示文摘Surface and interface engineering plays a crucial role in modulating the properties of materials,especially two-dimensional(2D)materials.Hence,a strategy,forming heterostructures with MoS_(2),is proposed to overcome the natural agglomeration of Ti_(3)C_(2)T_(x) MXene nanosheets.Most importantly,the interactions between Ti_(3)C_(2)Tx and MoS_(2) were elaborately investigated by first-principles calculations based on density functional theory(DFT)for the first time.The calculations demonstrate that van der Waals forces dominate the interface interactions of Ti_(3)C_(2)T_(x) and MoS_(2),rendering Ti_(3)C_(2)T_(x)@MoS_(2) heterostructures favorable stability.The Ti_(3)C_(2)T_(x)@MoS_(2) heterostructure composites were synthesized through a facile one-step hydrothermal method and exhibit a 2D hierarchical structure.Furthermore,the corrosion and tribological properties of epoxy composite coatings with varying proportions of Ti_(3)C_(2)T_(x)@MoS_(2) composites were studied in detail.As a result,the epoxy composite coating with 0.1 wt.%Ti_(3)C_(2)T_(x)@MoS_(2) composites(Ti_(3)C_(2)T_(x)@MoS_(2)-0.1)exhibits excellent corrosion protection and antiwear performances.The Ti_(3)C_(2)T_(x)@MoS_(2)-0.1 keeps the largest low-frequency impedance modulus(|Z|_(0.)01 Hz)and coating resistance(R_(c))during the whole immersion period.Its wear rate is 0.09μm^(3)/(Nμm)under the load of 10 N,one half of that of pure epoxy coating(EP).This work further broadens the application of MXene-based heterostructure composites. | Meng Cai Peng Feng Han Yan Yuting Li Shijie Song Wen Li Hao Li Xiaoqiang Fan Minhao Zhu | 2022 | Journal of Materials Science & Technology2022，，21： | 1 |
| 7 | Synergistic lubrication of few-layer Ti_(3)C_(2)T_(x)/MoS_(2) heterojunction as a lubricant additive显示文摘The few-layer Ti_(3)C_(2)T_(x)/MoS_(2) heterostructure was successfully prepared via vertically growing of MoS_(2) nanosheets on the few-layer Ti3C2Tx matrix using hydrothermal method.The tribological properties as additive in mineral oil(150N)were evaluated in detail.The 0.3 wt% of few-layer Ti_(3)C_(2)T_(x)/MoS_(2) heterostructure addition amount can reduce the friction and wear of 150N by 39% and 85%,respectively.Moreover,the enhancement effect of few-layer Ti_(3)C_(2)T_(x)/MoS_(2) on tribological properties of 150N is superior to that of few-layer Ti_(3)C_(2)T_(x),MoS_(2) nanosheets,and their mechanical mixture.Based on the characterization and analysis of wear debris and wear track,such excellent tribological properties of the few-layer Ti_(3)C_(2)T_(x)/MoS_(2) heterostructure derive from its structural advantage toward good dispersion,the synergistic lubrication of Ti_(3)C_(2)T_(x) and MoS_(2) nanosheets during the rubbing process,and the formation of tribo-film. | Peng FENG Yanping REN Yuting LI Jifan HE Zhuang ZHAO Xiaoliang MA Xiaoqiang FAN Minhao ZHU | 2022 | Friction2022，10，12： | 1 |
| 8 | Hepatitis B virus infection eontributes to oxidative stress in a population exposed to aflatoxin B1 and high risk for hepatocellular carcinoma显示文摘 | Liu Zhiming Li Lequn Peng Minhao | 2008 | Cancer Lett2008，263，2： | 1 |
| 9 | Extended pancreatoduodenectomy with portal vein and inferior vena cava resection and reconstruction combined with sorafenib for hepatoid carcinoma of the pancreas:a strategy of superextended surgery combined with targeted therapy显示文摘Hepatoid carcinoma of the pancreas(HCP)is an extremely rare pancreatic cancer resembling hepatocellular carcinoma,a type of liver cancer(1).Most reports have shown that it has an aggressive behavior and is associated with early metastasis.There is no standardized treatment for HCP due to its rarity,and the limited number of cases reported in the literature(2,3).However,treatment options for this type of rare cancer include surgery,chemotherapy,and radiation therapy,depending on the stage of the cancer.Nevertheless,the prognosis of HCP is poor. | Deling Wei Banghao Xu Hai Zhu Jilong Wang Zongrui Jin Weitao Chen Jianyong Zhang Zhujing Lan Keyu Huang Ling Zhang Tingting Lu Ni Fang Ya Guo Tao Peng Minhao Peng Zhang Wen | 2023 | Hepatobiliary Surgery and Nutrition2023，12，4： | 0 |
| 10 | Optimization of several surface treatment processes for alleviating fretting damage of a locking pin显示文摘The operational safety and reliability of a variable gauge train are affected by the anti-fretting wear performance of the locking mechanism.The main purpose of this study is to optimize the surface treatment process for a locking pin material under actual service conditions to alleviate fretting damage.Based on the two basic principles of surface strengthening and friction reduction,a substrate(AISI 4135 steel)surface was treated by laser quenching(LQ),plasma nitriding(PN),and bonded MoS2 coating.Systematic fretting wear tests were conducted,and the wear behavior and damage mechanism of various treated surfaces were comprehensively investigated.The results indicate that the wear resistances of the LQ-and PN-treated surfaces were significantly improved,and their main wear mechanisms were abrasive wear,delamination,and oxidation wear.The MoS_(2) coating exhibits the lowest friction coefficient and energy dissipation due to its self-lubricating property,but it incurs the highest wear rate and failure in the form of plastic deformation.Furthermore,the rough compound layer with a high hardness on the PN-treated surface is conducive to the formation and maintenance of the third-body contact at the fretting interface,consequently resulting in a significant reduction in wear.An optimal surface treatment process for alleviating fretting damage of the locking pin is recommended via comprehensive evaluation,which provides a reference for the anti-fretting protection of related mechanical components. | Jifan HE Zhenbing CAI Yanping REN Jinfang PENG Jianhua LIU Minhao ZHU | 2022 | Friction2022，10，8： | 0 |
| 11 | Effect of body mass index on the operation time and postoperative hospital stay of retroperitoneal laparoscopic renal cyst decortication显示文摘Objective:To investigate the effect of body mass index(BMI)on the operation time and postoperative hospital stay for patients who underwent retroperitoneal laparoscopic decortication for a single simple renal cyst.Methods:A retrospective cohort study was conducted among 81 patients with single simple renal cyst who had undergone retroperitoneal laparoscopic cyst decortication from January 2017 to December 2019 in Wuxi Xishan People's Hospital.All patients were divided into three groups according to BMI:normal group(BMI<25 kg/m^(2),n=44),overweight group(BMI=25-30 kg/m^(2),n=21),and obese group(BMI>30 kg/m^(2),n=16).Multiple linear regression was conducted to investigate the correlation.Results:The three groups were comparable in terms of age,gender,maximum diameter of cyst,and cyst location.In the aspect of operation time,only the patients in obese group had longer duration when compared with those in the normal group(59.1±15.7 min vs.45.2±12.8 min,p=0.001).And the patients in the obese group had significantly longer hospital stay compared with those in the normal group(6.2±1.9 d vs.5.2±0.5 d,p=0.002)and overweight group(6.2±1.9 d vs.5.0±1.0d,p=0.001).In the analysis of multiple linear regression,it was found that operation time is significantly affected by BMI and location 2,with coefficients of 1.299 and -8.646 respectively.The influence of BMI was greater than location 2(0.335 vs.-0.289).For hospital stay,only BMI had an effect on it,with a coefficient of 0.110.Conclusion:BMI was a major factor that associated with longer operation time and hospital stay in patients with retroperitoneal laparoscopic renal cyst decortication. | Peng Gu Meilin Li Minhao Zhang Xiaoliang He | 2021 | Laparoscopic, Endoscopic and Robotic Surgery2021，4，2： | 0 |
| 12 | Friction and Wear Properties of High-velocity Oxygen Fuel Sprayed WC-17Co Coating under Rotational Fretting Conditions显示文摘Rotational fretting which exist in many engineering applications has incurred enormous economic loss. Thus, accessible methods are urgently needed to alleviate or eliminate damage by rotational fretting. Surface engineering is an effective approach that is successfully adopted to enhance the ability of components to resist the fretting damage. In this paper, using a high-velocity oxygen fuel sprayed(HVOF) technique WC-17 Co coating is deposited on an LZ50 steel surface to study its properties through Vickers hardness testing, scanning electric microscope(SEM), energy dispersive X-ray spectroscopy(EDX), and X-ray diffractrometry(XRD). Rotational fretting wear tests are conducted under normal load varied from 10 N to 50 N, and angular displacement amplitudes vary from 0.125° to 1°. Wear scars are examined using SEM, EDX, optical microscopy(OM), and surface topography. The experimental results reveal that the WC-17 Co coating adjusted the boundary between the partial slip regime(PSR) and the slip regime(SR) to the direction of smaller amplitude displacement. As a result, the coefficients of friction are consistently lower than the substrate's coefficients of friction both in the PSR and SR. The damage to the coating in the PSR is very slight. In the SR, the coating exhibits higher debris removal efficiency and load-carrying capacity. The bulge is not found for the coating due to the coating's higher hardness to restrain plastic flow. This research could provide experimental bases for promoting industrial application of WC-17 Co coating in prevention of rotational fretting wear. | LUO Jun CAI Zhenbing MO Jiliang PENG Jinfang ZHU Minhao | 2016 | Chinese Journal of Mechanical Engineering2016，29，3： | 0 |
您所在的机构暂未开通此部分的功能，请联系管理员