|
|
|
题名
|
作者
|
年代
|
出处
|
被引量
|
| 1 | Modified room temperature solid-state synthesis of yttria-stabilized zirconia(YSZ) nano-powders for solid oxide fuel cells显示文摘High-performance solid oxide fuel cell(SOFC) is in urgent need of high-quality electrolyte powders with high reactivity and chemical uniformity.Here,8 mol% Y_(2)O_(3) doped ZrO_(2)(YSZ) nano-powders were synthesized by an improved solid-state reaction method at ambient temperature,and were applied to the fabrication of SOFC electrolytes.YSZ nano-powders show average grain sizes of ^(2)0 nm and high dispersibility,which is comparable with or even better than some other chemical methods.Benefitting from their high reactivity,dense YSZ electrolytes(relative density of 97.9%) can be obtained at a relatively low sintering temperature of 1400℃.The optimized electrical conductivity reaches up to a high value of0.034 S/cm at 800 0C in air.The anode supported single cell with the construction of Ni-YSZ/YSZ/Sm_(0.2)Ce_(0.8)O_(2-δ)(SDC)/La_(0.6)Sr_(0.4)Co_(0.2)Fe_(0.8)O_(3-δ)(LSCF) exhibits the peak power density of 0.827 W/cm^(2) at800℃ while taking wet H_(2) as fuels and ambient air as oxidants. | Xiaoqian Xu Yurun Feng Zhaoyu Zhong Xue Guo Zhenhao Zhang Jiao Li Shikai Zhao Shigang Wu Haibin Sun | 2023 | Journal of Rare Earths2023，41，9： | 0 |
| 2 | Extraction of Flavonoids from Leaves of Coix lacryma-jobi L.显示文摘[Objectives] To extract the flavonoids from leaves of Coix lacryma-jobi L. [Methods] Ethanol extraction method was adopted,spectrophotometry was used,and single factor experiment and orthogonal experiment were carried out to study the effects of ethanol percentage,extraction temperature,solid-to-liquid ratio and extraction time on the extraction of total flavonoids from leaves of C. lacryma-jobi L.[Results] The order of 4 factors influencing the extraction of flavonoids from leaves of C. lacryma-jobi L. was: solid-to-liquid ratio > extraction time > ethanol percentage > extraction temperature. When the extraction temperature was 70℃,the extraction time was 1. 5 h and the solid-liquid ratio was 1: 10,the ethanol percentage was 60%,the extraction effect was the best,extraction of flavonoids was 0. 107 5 mg/m L.[Conclusions] This study is expected to provide a theoretical basis for further development and utilization of C. lacryma-jobi L. | Xiaoxiong FENG Yurun LIANG Aiyue LUO Jiandan NONG Shaomei MO Yan NING Suoyi HUANG | 2018 | Medicinal Plant2018，9，1： | 0 |
| 3 | Dielectric properties of porous SiC/Si3N4 ceramics by polysilazane immersion-pyrolysis显示文摘The SiC nanotubes were synthesized on porous Si3N4 matrix by polysilazane immersion-pyrolysis. The β-SiC and free C contents increased with the increasing dipping times, which cause some clear vibration and loss peaks of the dielectric constant patterns emerged at around 12.9 GHz and 14.7 GHz in the samples of 20 wt% and 30 wt%benzoic acid, respectively. The reflectivity of the obtained ceramics were -7 dB ^-10 dB from the frequency of 8 GHz–18 GHz, which means that the amount of 80%–90% electromagnetic wave could be attenuated. The ceramics containing 40 wt% benzoic acid showed the high loss, low reflectivity and a wide absorbing band,indicating the high absorbing efficiency and good dielectric properties. | Xiao Lin Hongyu Gong Yujun Zhang Jianqiang Bi Yurun Feng Yu Liu Shan Wang | 2019 | Progress in Natural Science:Materials International2019，29，2： | 0 |
| 4 | Additive Manufacturing of Ceramics from Liquid Feedstocks显示文摘In this review,we summarize the research activities carried out by our research group at the University of Padova on the additive manufacturing of ceramics from liquid feedstocks.Particularly,we evaluate the use of preceramic polymers,geopolymers,and sol-gel solutions.We mainly focus on processing with liquid feedstocks because they have some advantages with respect to slurry-based feedstocks in which powders are present.Particularly,lower viscosity,enhanced transparency,and lack of scattering and sedimentation are advantageous features for vat photopolymerization processes,whereas the absence of particulates reduces clogging problems at the nozzle for extrusion-based processes.Simultaneously,preceramic polymers and geopolymers have some limitations in terms of the range of ceramic compositions that can be obtained;sol-gel solutions are intrinsically unstable,whereas printed objects suffer from drying issues.Nevertheless,we successfully produced high-quality parts using a variety of additive manufacturing techniques,some of which(e.g.,volumetric additive manufacturing)have been proposed for the fabrication of ceramic components for the first time. | Giorgia Franchin Hamada Elsayed Renata Botti Kai Huang Johanna Schmidt Giulio Giometti Alice Zanini Anna De Marzi Marco D’Agostini Paolo Scanferla Yurun Feng Paolo Colombo | 2022 | Chinese Journal of Mechanical Engineering(Additive Manufacturing Frontiers)2022，1，1： | 0 |
您所在的机构暂未开通此部分的功能，请联系管理员