|
|
|
题名
|
作者
|
年代
|
出处
|
被引量
|
| 1 | Surface integrity of GH4169 affected by cantilever finish grinding and the application in aero-engine blades显示文摘GH4169 is the main material for aero-engine blades and integrated blisks. Because GH4169 has a poor milling performance, the profile precision and surface integrity of blades and integrated blisks are difficult to be met by utilizing the conventional milling process, which directly influence the global performance and reliability of aero-engines. Through grinding experiments on parameters and surface integrity optimization, the helical cantilever grinding process utilizing a300# CBN RB wheel is presented and applied in finish machining of GH4169 blades. The profile errors of the blade surface are within ±0.01 mm, the roughness is less than 0.4 lm, the residual compressive stresses and the hardening rate are appropriate, there are no phenomena of burr and smearing with the grinding chips, and the leading/trailing edge can be smoothly connected with the suction/pressure surface. All the experimental results indicate that this grinding process is greatly suitable for the profile finish machining of GH4169 blades. | Li Xun Ma Shuang Meng Fanjun | 2015 | Chinese Journal of Aeronautics2015，28，5： | 9 |
| 2 | Surface nanostructure formation mechanism of 45 steel induced by supersonic fine particles pombarding显示文摘By means of supersonic fine particles bombarding (SFPB),a nanostructured surface layer up to 15 μm was fabricated on a 45 steel plate with ferrite and pearlite phases. To reveal the grain refinement mechanism of SFPB-treated 45 steel,microstructure features of various sections in the treated surface were systematically characterized by X-ray diffraction (XRD),scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Grain size increases with an increase of depth from the treated surface. Plastic deformation and grain refinement processes are accompanied by an increase in strain. Plastic deformation in the proeutectoid ferrite phases has precedence over the pearlite phases. Grain refinement in the ferrite phases involves: the onset of dis-location lines (Dls),dislocation tangles (DTs) and dense dislocation walls (DDWs) in the original grains; the formation of fine la-mellar and roughly equiaxed cells separated by DDWs; by dislocation annihilation and rearrangement,the transformation of DDWS into subboundaries and boundaries and the formation of submicron grains or subgrains; the successive subdivision of grains to finer and finer scale,resulting in the formation of highly misoriented nano-grains. By contrast,eutectoid cementite phase accommodated strain in a sequence as follows: onset of elongated,bended and shear deformation under deformation stress of ferrites,short and thin cementites with a width of about 20-50 nm and discontinuous length were formed. Shorter and thinner cementites were developed into ultra-fine pieces under the action of high density dislocation and strains. At the top surface,some cementites were decomposed under severe plastic deformation. Experimental evidences and analysis indicate that surface nanocrystallization of 45 steel results from dislocation activities,high strains and high strain rate are necessary for the formation of nanocrystallites. | Dema Ba Shining Ma Changqing Li Fanjun Meng | 2008 | Journal of University of Science and Technology Beijing2008，15，5： | 3 |
| 3 | Structural characteristics and deep-water hydrocarbon accumulation model of the Scotian Basin, Eastern Canada显示文摘Commercial hydrocarbon reservoirs have been discovered in shallow-water areas of the Scotian Basin, Eastern Canada. However, knowledge about the structure and hydrocarbon accumulation characteristics of the basin is still insufficient, which constrains the oil and gas exploration in deep-water areas. Based on comprehensive data of magnetic anomalies, seismic survey, and drilling, this study determines the structure characteristics of the Scotian Basin and its hydrocarbon accumulation conditions in deep waters and evaluates the deep-water hydrocarbon exploration potential. The transform faults and basement structures in the northern basin control the sedimentary framework showing thick strata in east and thin strata in west of the basin. The bowl-shaped depression formed by thermal subsidence during the transitional phase and the confined environment (micro basins) caused by salt tectonics provide favorable conditions for the development of source rocks during the depression stage (also referred to as the depression period sequence) of the basin. The progradation of large shelf-margin deltas during the drift phase and steep continental slope provide favorable conditions for the deposition of slope-floor fans on continental margins of the basin. Moreover, the source-reservoir assemblage comprising the source rocks within the depression stage and the turbidite sandstones on the continental margin in the deep waters may form large deep-water turbidite sandstone reservoirs. This study will provide a valuable reference for the deep-water hydrocarbon exploration in the Scotian Basin. | Gaokui Wu Fanjun Kong Naxin Tian Tianbi Ma Chongzhi Tao | 2023 | Energy Geoscience2023，4，3： | 1 |
| 4 | Effect of cool- ing rates on the second-phase precipitation and proeutectoid phase transformation of a Nb-Ti microalloyed steel slab 显示文摘 | Ma Fanjun Wen Guanghua Wang Wanlin | 2013 | Steel Research Int2013，84，4： | 1 |
您所在的机构暂未开通此部分的功能，请联系管理员