|
|
|
题名
|
作者
|
年代
|
出处
|
被引量
|
| 1 | Design,modeling and experiments of broadband tristable galloping piezoelectric energy harvester显示文摘Galloping based piezoelectric energy harvester is a kind of micro-environmental energy harvesting device based on flowinduced vibrations.A novel tristable galloping-based piezoelectric energy harvester is constructed by introducing a nonlinear magnetic force on the traditional galloping-based piezoelectric energy harvester.Based on Euler-Bernoulli beam theory and Kirchhoff’s law,the corresponding aero-electromechanical model is proposed and validated by a series of wind tunnel experiments.The parametric study is performed to analyse the response of the tristable galloping-based piezoelectric energy harvester.Numerical results show that comparing with the galloping-based piezoelectric energy harvester,the mechanism of the tristable galloping-based piezoelectric energy harvester is more complex.With the increase of a wind speed,the vibration of the bluff body passes through three branches:intra-well oscillations,chaotic oscillations,and inter-well oscillations.The threshold wind speed of the presented harvester for efficiently harvesting energy is 1.0 m/s,which is decreased by 33% compared with the galloping-based piezoelectric energy harvester.The maximum output power of the presented harvester is 0.73 mW at 7.0 m/s wind speed,which is increased by 35.3%.Compared with the traditional galloping-based piezoelectric energy harvester,the presented tristable galloping-based piezoelectric energy harvester has a better energy harvesting performance from flow-induced vibrations. | Junlei Wang Linfeng Geng Shengxi Zhou Zhien Zhang Zhihui Lai Daniil Yurchenko | 2020 | Acta Mechanica Sinica2020，36，3： | 9 |
| 2 | Synthesis of graphene on a Ni film by radio-frequency plasma-enhanced chemical vapor deposition显示文摘Large-area single-or multilayer graphene of high quality is synthesized on Ni films by radio-frequency plasma-enhanced chemical vapor deposition (RF-PECVD) at a relatively low temperature (650℃).In the deposition process,a trace amount of CH4 gas (2-8 sccm (sccm denotes standard cubic centimeter per minute at STP)) is introduced into the PECVD chamber and only a short deposition time (30-60 s) is used.Single-or multilayer graphene is obtained because carbon atoms from the discharging CH4 diffuse into the Ni film and then segregate out at its surface.The layer number of the obtained graphene increases when the deposition time or CH4 gas flow rate is increased.This investigation shows that PECVD is a simple,low-cost,and effective technique to synthesize large-area single-or multilayer graphene,which has potential for application as electronic devices. | QI JunLei ZHANG LiXia CAO Jian ZHENG WeiTao WANG Xin FENG JiCai | 2012 | Chinese Science Bulletin2012，57，23： | 8 |
| 3 | Bile acids evoke placental inflammation by activating Gpbar1/NF-κB pathway in intrahepatic cholestasis of pregnancy显示文摘Intrahepatic cholestasis of pregnancy(ICP)is a cholestatic disorder with potentially deleterious consequences for fetuses.Although a clear correlation between the elevated levels of maternal serum bile acids and deficient fetal outcome has been established in clinical practice,the underlying mechanisms remain elusive.Herein,we report that bile acids induce NF-κB pathway activation via G protein-coupled bile acid receptor 1(Gpbar1),with consequent upregulation of inflammatory genes in trophoblasts,leading to aberrant leukocyte infiltration and inflammation in placenta.Ursodeoxycholic acid(UDCA),a drug used clinically to treat ICP,competes with other bile acids for binding with Gpbar1 and thus inhibits bile acid-induced inflammatory response in trophoblasts and improves fetal survival in pregnant rats with obstructive cholestasis.Notably,inhibition of NF-κB by andrographolide is more effective than UDCA in benefiting placentas and fetuses.Thus,anti-inflammation therapy targeting Gpbar1/NF-κB pathway could be effective in suppressing bile acid-induced inflammation and alleviating ICP-associated fetal disorders. | YouHua Zhang YouDong Pan ChangDong Lin YaJuan Zheng Hao Sun HaiLong Zhang JunLei Wang MengYa Yuan Tao Duan QiaoLing Du JianFeng Chen | 2016 | Journal of Molecular Cell Biology2016，8，6： | 8 |
| 4 | Attitude control for QTR using exponential nonsingular terminal sliding mode control显示文摘For the problem of attitude control of a quad tilt rotor aircraft with unknown external disturbances, a class of control methods based on a new exponential fast nonsingular terminal sliding surface, a new fast reaching law, and a super twisting sliding mode disturbance observer is investigated. First, the new exponential nonsingular terminal sliding surface is designed by using the advantages of nonsingular terminal sliding mode finite time convergence and strong robustness. Second, to solve the problem of a long convergence time and the serious shaking of the traditional reaching law, a new fast reaching law model with characteristics of the second-order sliding mode is put forward. Third,considering the existence of complex disturbances, the super twisting sliding mode disturbance observer is used to estimate and compensate the composite disturbances online. Finally, compared with the traditional nonsingular fast sliding mode control, simulation results show that the proposed control scheme achieves a good control performance. | LIU Haibo WANG Heping SUN Junlei | 2019 | Journal of Systems Engineering and Electronics2019，30，1： | 5 |
| 5 | Materials evolution of bone plates for internal fixation of bone fractures:A review显示文摘Bone plates play a vital role in bone fracture healing by providing the necessary mechanical fixation for fracture fragments through modulating biomechanical microenvironment adjacent to the fracture site.Good treatment effect has been achieved for fixation of bone fracture with conventional bone plates,which are made of stainless steel or titanium alloy.However,several limitations still exist with traditional bone plates including loosening and stress shielding due to significant difference in modulus between metal material and bone tissue that impairs optimal fracture healing.Additionally,due to demographic changes and non-physiological loading,the population suffering from refractory fractures,such as osteoporosis fractures and comminuted fractures,is increasing,which imposes a big challenge to traditional bone plates developed for normal bone fracture repair.Therefore,optimal fracture treatment with adequate fixation implants in terms of materials and design relevant to special conditions is desirable.In this review,the complex physiological process of bone healing is introduced,followed by reviewing the development of implant design and biomaterials for bone plates.Finally,we discuss recent development of hybrid bone plates that contains bioactive elements or factors for fracture healing enhancement as a promising direction.This includes biodegradable Mg-based alloy used for designing bone screw-plates that has been proven to be beneficial for fracture healing,an innovative development that attracts more and more attention.This paper also indicates that the tantalum bone plates with porous structure are also emerging as a new fracture internal fixation implants.The reduction of the stress shielding is verified to be useful to accelerate bone fracture healing.Potential application of biodegradable metals may also avoid a second operation for implant removal.Further developments in biometals and their design for orthopedic bone plates are expected to improve the treatment of bone fracture,especially the refractory fractures. | Junlei Li Ling Qin Ke Yang Zhijie Ma Yongxuan Wang Liangliang Cheng Dewei Zhao | 2020 | Journal of Materials Science & Technology2020，36，1： | 5 |
| 6 | Zircon SHRIMP geochronology and Nd-Pb isotopic characteristics of the meta-basalt in the central part of Tibetan Plateau's Qiangtang region显示文摘A small-sized meta-basic rock system is discovered in Qilongwuru Gully of Central Qiangtang’s Shuanghu region and contains a meta-basalt and garnet-bearing plagioclase amphibolite.The zircon U/Pb age of this meta-basalt by SHRIMP analysis is463.3±4.7 Ma,suggesting that this lava formed in the Middle Ordovician,and is consistent with that of the meta-basic rocks in the Taoxing Lake and Guoganjianian Mountain ophiolite found in the Qiangtang plate.As this lava system bears similar geochemistry to N-MORB,it might be a component of ophiolite that represents the trail of the extinction of the Proto-Tethys,suggesting that the formation of Proto-Tethys oceanic basin in the Longmu Co-Shuanghu suture zone could date as far back as to the Middle Ordovician.Isotopic geochemical analysis indicates that the magma source area consists of both depleted mantle(DM)and enriched mantle(EMII)end members and bears Dupal anomaly,similar to that of the Paleo-Tethys in the Neo-Tethys represented by the Yarlung-Tsangpo suture zone,the Paleo-Tethys represented by the Changning-Menglian suture zone,and the Paleo-Tethys in Sanjiang region.This suggests that they have inherited the attribute of the Proto-Tethys mantle domain,and the Longmu Co-Shuanghu suture zone may be a representative of the northern boundary of Gondwana. | PENG ZhiMin GENG QuanRu PAN GuiTang WANG LiQuan ZHANG Zhang CONG Feng GUAN JunLei | 2014 | Science China Earth Sciences2014，57，3： | 5 |
| 7 | Effects of atomization parameters of dust removal nozzles on the de-dusting results for different dust sources显示文摘In order to obtain appropriate spray pressure and enhance the spraying and dust removal efficiency, various factors including the dust characteristics, nozzle spraying angle, effective spraying range, water consumption and droplet size are taken into account. The dust characteristics from different mines and atomization parameters of different pressure nozzles were measured. It was found that the internal pressure of coal cutters and roadheaders should be kept at 2 MPa, which could ensure large droplet size, large spraying angle and low water consumption and hence realizing a large-area covering and capture for large particle dusts. However, the external spray pressure should be kept at 4 MPa for smaller droplet size and longer effective spraying range, leading to effective dust removal in the operator zone. The spray pressure of support moving, drawing opening, and stage loader on a fully mechanized caving face and stage loader on a fully mechanized driving face should be kept at 8 MPa, under which the nozzles have long effective spraying range, high water flow and small droplet size for the rapid capture of instantaneous, high-concentration and small size dust groups. From the applications on the caving and driving faces in the coal mines, it is indicated that the optimization of spray pressure in different spraying positions could effectively enhance dust removal efficiency. Selecting appropriate nozzles according to the dust characteristics at different positions is also favorable for dust removal efficiency. With the selected nozzles under optimal pressures, the removal rates of both total dust and respirable dust could reach over70%, showing a significant de-dusting effect. | Cheng Weimin Ma Youying Yang Junlei Sun Biao | 2016 | International Journal of Mining Science and Technology2016，26，6： | 4 |
| 8 | New Evidence of Detrital Zircon Ages for the Final Closure Time of the Paleo-Asian Ocean in the Eastern Central Asian Orogenic Belt(NE China)显示文摘Objective The NE China is located in the eastern segment of the Central Asian Orogenic Belt(CAOB),which is a large accretionary orogen between the Siberian Craton and the North China Craton(NCC).Many researches have discussed about the evolution of the Paleo-Asian Ocean(PAO)in the eastern CAOB.However,the timing of | DU Qingxiang HAN Zuozhen SHEN Xiaoli HAN Chao SONG Zhigang GAO Lihua HAN Mei ZHONG Wenjian YAN Junlei | 2017 | Acta Geologica Sinica(English Edition)2017，91，5： | 4 |
| 9 | Modification strategies on transition metal-based electrocatalysts for efficient water splitting显示文摘Electrocatalytic water splitting driven by electrocatalysts is recognized as a promising strategy to generate clean hydrogen fuel.Searching and constructing high-efficient and low-cost electrocatalysts is vital in the practical applications of electrocatalytic water splitting.Although transition metal-based materials have been considered as promising electrocatalysts,the satisfactory activities are usually not built on the bulk materials,but strongly relying on elaborately designing these electrocatalysts.Herein,the recent theoretical and experimental progress on modification strategies to improve the intrinsic activities is summarized,especially including element doping,phase engineering,structure cooperation,interface engineering,vacancy engineering,strain engineering and self-functionalization.Finally,the future opportunities and challenges on these modification strategies are also proposed.Overall,it is anticipated that these modification strategies offer some new understandings on rationally constructing non-noble electrocatalysts for efficient electrocatalytic water splitting. | Yaotian Yan Pengcheng Wang Jinghuang Lin Jian Cao Junlei Qi | 2021 | Journal of Energy Chemistry2021，30，7： | 4 |
| 10 | Inhibition effects of benzalkonium chloride on Chlorella vulgaris induced corrosion of carbon steel显示文摘In this work,a surfactant,benzalkonium chloride(BAC),was used to study its effects on both the growth of Chlorella vulgaris and the corrosion caused by its biofilm.Experimental results indicated that BAC at a low concentration of 3 mg/L suppressed C.vulgaris growth and achieved 81%corrosion inhibition based on weight loss reduction.The inhibition effects increased when the BAC dosage was increased.At 30 mg/L,the corrosion inhibition increased to 95%.Electrochemical results supported surface pitting analysis,weight loss results data and confirmed the corrosion inhibition. | Junlei Wang Tiansui Zhang Xinxin Zhang Muhammed Asif Lipei Jiang Shuang Dong Tingyue Gu Hongfang Liu | 2020 | Journal of Materials Science & Technology2020，36，8： | 4 |
| 11 | 儿童福利机构中的类家庭养育显示文摘创设类家庭养育模式
类家庭养育与传统机构养育的不同
类家庭养育模式在很多方面的优势对幼童的健康成长是至关重要的。从结构角度来看,家庭由相对较小的团体构成,尤其是相对少的儿童。如果孩子不止一个,那么不同年龄、性别、或者有特殊需要的儿童都住在一起。 | Robert B.McCall Christina J.Groark Junlei Li 曾凡林 | 2009 | 社会福利(实务版)2009，，12： | 3 |
| 12 | Porous g-C3N4 with enhanced adsorption and visible-light photocatalytic performance for removing aqueous dyes and tetracycline hydrochloride显示文摘Porous g-C_3N_4samples were obtained by simply calcining bulk g-C_3N_4in static air in a muffle oven.The photocatalytic performance of these samples was evaluated through the removal of aqueous organic dyes(methylene blue and methyl orange)and tetracycline hydrochloride under visible-light irradiation(λ>420 nm).Compared to bulk g-C_3N_4,porous g-C_3N_4exhibited much better capability for removing these contaminants,especially under visible-light irradiation,due to the enlarged specific surface area and more efficient separation of photogenerated charge carries.In particular,porous g-C_3N_4obtained by calcining bulk g-C_3N_4in air at 525°C showed the highest visible-light-driven catalytic activity among these samples.Superoxide radical anions(·O_2^-)were found to be the primary active species responsible for photodegradation. | Junlei Zhang Zhen Ma | 2018 | Chinese Journal of Chemical Engineering2018，26，4： | 3 |
| 13 | Households' Risk Perception and Behavioral Responses to Natech Accidents显示文摘This study analyzes data on households' risk perception and protective behavior following a natural disaster triggered technological accident(Natech accident)that occurred at an industrial park in Sendai during the Great East Japan Earthquake and Tsunami, on 11 March2011. The results indicate that some households carried out multiple evacuations and that households' risk perceptions changed throughout the Natech accident evacuation process. Risk perception differed according to household location and demographic characteristics. We also found differences in the protective measures adopted for households in different locations. Specifically, those living closer to the Natech accident tended to evacuate immediately,whereas those living further away tended to shelter in place. Wind direction is discussed as a factor that influences households' risk perception and evacuation response to a Natech accident. The findings of this study advance knowledge of household behavior in response to a Natech accident and can assist emergency managers in developing strategies for better management of evacuation processes. | Junlei Yu Ana Maria Cruz Akihiko Hokugo | 2017 | International Journal of Disaster Risk Science2017，8，1： | 2 |
| 14 | Multi-example feature-constrained back-projection method for image super-resolution显示文摘Example-based super-resolution algorithms,which predict unknown high-resolution image information using a relationship model learnt from known high- and low-resolution image pairs, have attracted considerable interest in the field of image processing. In this paper, we propose a multi-example feature-constrained back-projection method for image super-resolution. Firstly, we take advantage of a feature-constrained polynomial interpolation method to enlarge the low-resolution image. Next, we consider low-frequency images of different resolutions to provide an example pair. Then, we use adaptive k NN search to find similar patches in the low-resolution image for every image patch in the high-resolution low-frequency image, leading to a regression model between similar patches to be learnt. The learnt model is applied to the low-resolution high-frequency image to produce high-resolution high-frequency information. An iterative back-projection algorithm is used as the final step to determine the final high-resolution image.Experimental results demonstrate that our method improves the visual quality of the high-resolution image. | Junlei Zhang Dianguang Gai Xin Zhang Xuemei Li | 2017 | Computational Visual Media2017，3，1： | 2 |
| 15 | Pyrochlore-based high-entropy ceramics for capacitive energy storage显示文摘High-performance dielectrics are widely used in high-power systems,electric vehicles,and aerospace,as key materials for capacitor devices.Such application scenarios under these extreme conditions require ultra-high stability and reliability of the dielectrics.Herein,a novel pyrochlore component with high-entropy design of Bi1.5Zn_(0.75)Mg_(0.25)Nb_(0.75)Ta_(0.75)O_(7)(BZMNT)bulk endows an excellent energy storage performance of Wrec≈2.72 J/cm3 together with an ultra-high energy efficiency of 91%at a significant enhanced electric field Eb of 650 kV/cm.Meanwhile,the temperature coefficient(TCC)of BZMNT(~−220 ppm/℃)is also found to be greatly improved compared with that of the pure Bi1.5ZnNb1.5O7(BZN)(~−300 ppm/℃),demonstrating its potential application in temperature-reliable conditions.The high-entropy design results in lattice distortion that contributes to the polarization,while the retardation effect results in a reduction of grain size to submicron scale which enhances the Eb.The high-entropy design provides a new strategy for improving the high energy storage performance of ceramic materials. | Yiying CHEN Junlei QI Minhao ZHANG Zixi LUO Yuan-Hua LIN | 2022 | Journal of Advanced Ceramics2022，11，7： | 2 |
| 16 | Multiplex imaging reveals the architecture of the tumor immune microenvironment显示文摘The tumor immune microenvironment(TME)is composed of a variety of components,such as tumor cells,immune cells,and the extracellular matrix.The TME has been studied through transcriptomic,proteomic,metabolomic,and phosphoproteomic approaches,which have provided researchers with a wealth of TME-related molecular information. | Junlei Zhang Jinyuan Song Jianpeng Sheng Xueli Bai Tingbo Liang | 2021 | Cancer Biology & Medicine2021，18，4： | 2 |
| 17 | Metal-organic framework MIL-53(Al): synthesis, catalytic performance for the Friedel-Crafts acylation, and reaction mechanism显示文摘Metal-organic framework MIL-53(Al) was synthesized by a solvothermal method using aluminum nitrate as the aluminium source and 1,4-benzenedicarboxylic acid(H2BDC) as the organic ligand. The structure of samples was characterized by X-ray diffraction(XRD) and Fourier transform infrared spectroscopy(FT-IR). The catalytic activity and recyclability of MIL-53(Al) catalyst for the Friedel-Crafts acylation reaction of indole with benzoyl chloride were evaluated. The reaction conditions were optimized and a reaction mechanism was suggested. The results showed that the MIL-53(Al) catalyst exhibited good catalytic activity and recyclability for the Friedel-Crafts acylation reaction. When the molar ratio of indole and MIL-53(Al) catalyst was 1:0.06(n1:ncatalyst), the molar ratio of indole and benzoyl chloride was 1:3, and the solvent was dichloromethane, the conversion of indole could reach 97.1% and the selectivity of 3-acylindole could reach 81.1% at 25 °C after 8 h. The catalyst can be reused without significant degradation in catalytic activity. After the catalyst was reused five times, the conversion of indole was 87.6% and the selectivity of 3-acylindole was 79.5%. | Junlei Yan Sai Jiang Shengfu Ji Da Shi Hefei Cheng | 2015 | Science China Chemistry2015，58，10： | 2 |
| 18 | Microstructure design of C/C composites through electrochemical corrosion for brazing to Nb显示文摘Surface structure of C/C composites has been regulated through electrochemical corrosion at room temperature to modify the residual stress and improve the joining strength when brazed to Nb.The unique crevice corrosion in C/C composites is investigated to reveal the change of corrosion depth and fiber size.The interlacing zone of carbon fiber reinforced brazing alloy replaces the reaction layer in the original joint.Joining area is increased dramatically and the continuous crack will be hindered.The interlacing zone eliminates the stress concentration and relieves the residual stress through reducing the property mismatch.All advantages contribute to the joining quality of C/C–Nb.Shear strength of C/C–Nb joint with 80μm depth reached 37.7 MPa,which was 1.2 times higher than that of original joint.Surface structure design of C/C composites not only expands the application in structure component,but also exhibits the promising application in energy field. | Jin Ba Xu Ji Bin Wang Peixin Li Jinghuang Lin Jian Cao Junlei Qi | 2022 | Journal of Materials Science & Technology2022，，9： | 2 |
| 19 | Corrosion formation and phase transformation of nickel-iron hydroxide nanosheets array for efficient water oxidation显示文摘Designing earth-abundant electrocatalysts with high performance towards water oxidation is highly decisive for the sustainable energy technologies. This study develops a facile natural corrosion approach to fabricate nickel-iron hydroxides for water oxidation. The resulted electrode demonstrates an outstanding activity and stability with an overpotential of 275 mV to deliver 10 mA·cm^(−2). Experimental and theoretical results suggest the corrosion-induced formation of hydroxides and their transformation to oxyhydroxides would account for this excellent performance. This work not only provides an interesting corrosion approach for the fabrication of excellent water oxidation electrode, but also bridges traditional corrosion engineering and novel materials fabrication, which would offer some insights in the innovative principles for nanomaterials and energy technologies. | Lanqian Gong Huan Yang Hongming Wang Ruijuan Qi Junlei Wang Shenghua Chen Bo You Zehua Dong Hongfang Liu Bao Yu Xia | 2021 | Nano Research2021，14，12： | 2 |
| 20 | A quantitative study of the scale and distribution of tight gas reservoirs in the Sulige gas field, Ordos Basin, northwest China显示文摘Gas and water distribution is discontinuous in tight gas reservoirs,and a quantitative understanding of the factors controlling the scale and distribution of effective reservoirs is important for natural gas exploration.We used geological and geophysical explanation results,dynamic and static well test data,interference well test and static pressure test to calculate the distribution and characteristics of tight gas reservoirs in the H_(8) Member of the Shihezi Formation,Sulige gas field,Ordos Basin,northwest China.Our evaluation system examines the scale,physical properties,gas-bearing properties,and other reservoir features,and results in classification of effective reservoirs into types Ⅰ,Ⅱ,and Ⅲ that differ greatly in size,porosity,permeability,and saturation.The average thickness,length,and width of type Ⅰ effective reservoirs are 2.89,808,and 598 m,respectively,and the porosity is>10.0%,permeability is>1010^(–3)µm^(2),and average gas saturation is>60%.Compared with conventional gas reservoirs,tight gas effective reservoirs are small-scale and have low gas saturation.Our results show that the scale of the sedimentary system controls the size of the dominant microfacies in which tight gas effective reservoirs form.The presence of different types of interbeds hinders the connectivity of effective sand body reservoirs.The gas source conditions and pore characteristics of the reservoirs control sand body gas filling and reservoir formation.The physical properties and structural nature of the reservoirs control gas–water separation and the gas contents of effective reservoirs.The results are beneficial for the understanding of gas reservoir distribution in the whole Ordos Basin and other similar basins worldwide. | Chao LUO Ailin JIA Jianlin GUO Qing TIAN Junlei WANG Hun LIN Nanxin YIN Xuanbo GAO | 2021 | Frontiers of Earth Science2021，15，2： | 2 |
您所在的机构暂未开通此部分的功能，请联系管理员