|
|
|
题名
|
作者
|
年代
|
出处
|
被引量
|
| 1 | Active metal brazing of SiO2–BN ceramic and Ti plate with Ag–Cu–Ti+BN composite filler显示文摘SiO_2–BN ceramic and Ti plate were joined by active brazing in vacuum with Ag–Cu–Ti+BN composite filler.The effect of BN content,brazing temperature and time on the microstructure and mechanical properties of the brazed joints was investigated.The results showed that a continuous Ti N–Ti B_2reaction layer formed adjacent to the SiO_2–BN ceramic,whose thickness played a key role in the bonding properties.Four Ti–Cu compound layers,Ti_2Cu,Ti_3Cu_4,Ti Cu_2and Ti Cu_4,were observed to border Ti substrate due to the strong affinity of Ti and Cu compared with Ag.The central part of the joint was composed of Ag matrix,over which some fine-grains distributed.The added BN particles reacted with Ti in the liquid filler to form fine Ti B whiskers and Ti N particles with low coefficients of thermal expansion(CTE),leading to the reduction of detrimental residual stress in the joint,and thus improving the joint strength.The maximum shear strength of 31 MPa was obtained when 3 wt%BN was added in the composite filler,which was 158%higher than that brazed with single Ag–Cu–Ti filler metal.The morphology and thickness of the reaction layer adjacent to the parent materials changed correspondingly with the increase of BN content,brazing temperature and holding time.Based on the correlation between the microstructural evolution and brazing parameters,the bonding mechanism of SiO_2–BN and Ti was discussed. | Z.W.Yang C.L.Wang Y.Wang L.X.Zhang D.P.Wang J.C.Feng | 2017 | Journal of Materials Science & Technology2017，33，11： | 5 |
| 2 | MICROSTRUCTURAL STUDIES OF FRICTION STIR WELDED AZ31 MAGNESIUM ALLOY显示文摘Friction stir welding achieves the weld in solid phase by locally introducing frictional heating and plastic flow arising from rotation of the welding tool, which results in changes in the local microstructure of magnesium alloy. The purpose in the paper is to study the microstructures of friction stir welded AZ31 magnesium alloy. Residual microstructures, including dynamic re-crystallization zone and nugget structures have been systematically investigated utilizing optical microscopy (OM), scanning electric microscopy (SEM), transmission electron microscopy (TEM) with energy dispersive spectroscopy (EDS), X-ray diffraction (XRD) and micro-hardness. AZ31 magnesium alloy has been successfully friction stir welded and exhibits the variations of microstructure including dynamically recrystallized, equaxied grains in the weld nugget. Residual hardness in the nugget was found slightly lower than the parent but not too obvious. | H.Zhang S.B.Lin L.Wu J.C.Feng | 2004 | Acta Metallurgica Sinica(English Letters)2004，17，5： | 3 |
| 3 | EFFECT OF BRAZING TIME ON TiC CERMET/IRON JOINT BRAZED WITH Ag-Cu-Zn FILLER METAL显示文摘The brazing of TiC cermet to iron was carried out at 1223K for 5-20min using Ag-Cu-Zn filler metal. The formation phase and interface structure of the joints were investigated by electron probe microanalysis (EPMA), scanning electron microscopy (SEM) and X-ray diffraction (XRD), and the joint strength was tested by shearing method. The results showed: there occurred three new formation phases, Cu(s.s), FeNi and Ag(s.s) in TiC cermet/iron joint. The interface structure was expressed as TiC cermet/Cu(s.s)+FeNi/Ag(s.s)+a little Cu(s.s)+a little FeNi/Cu(s.s)+ FeNi/iron. With brazing time increasing, there appeared highest shear strength of the joints, the value of which was up to 252.2MPa when brazing time was 10min. | L.X.Zhang J.C.Feng Z.R.Li H.J.Liu | 2004 | Acta Metallurgica Sinica(English Letters)2004，17，1： | 1 |
您所在的机构暂未开通此部分的功能，请联系管理员