|
|
|
题名
|
作者
|
年代
|
出处
|
被引量
|
| 1 | Comparative study of microRNA profiling in keloid fibroblast and annotation of differential expressed microRNAs显示文摘蟹状肿是由于皮损害的异常愈合成长的像肿瘤的皮疤,没有有效 treatment.The 分子的机制位于 \O 下面蟹状肿致病仍然大部分未知。在这研究,我们比较了表示在导出蟹状肿的成纤维细胞和正常成纤维细胞之间介绍的 microRNA (miRNA )( 包括胎儿、成年的真皮的成纤维细胞) 由 miRNA microarray 分析。我们发现在导出蟹状肿的成纤维细胞的 miRNA 侧面与在 normalfibroblasts 的那些是不同的。九 miRNAs 是表示其六在蟹状肿成纤维细胞(KF ) 是显著地起来调整的差别,包括 miR-152, miR-23b-3p, miR-31-5p, miR-320c, miR-30a-5p,和 hsv1-miR-H7,并且其三是调整 significantlydown 的包括 miR-4328, miR-145-5p,和 miR-143-3p。差别的功能的注解表示了他们在为疤创伤愈合重要的几条发信号的小径被充实的 miRNA targetsrevealed。在结论,我们 demonstratethat miRNA 表示侧面在 KF 被改变与相比可以为探索蟹状肿的致病在胎儿、成年的真皮的成纤维细胞,和 expressionprofile 提供有用线索。miRNAs 可能部分由影响相关的几条发信号的小径使创伤愈合留下疤痕贡献 etiologyof 蟹状肿。 | Chao Li Yuehong Bai Hua Liu Xuemei Zuo Haichang Yao Yiming Xu Manlin Cao | 2013 | Acta Biochimica et Biophysica Sinica2013，45，8： | 15 |
| 2 | Effect of minor Sc addition on microstructure and stress corrosion cracking behavior of medium strength Al–Zn–Mg alloy显示文摘Influence of Sc content on microstructure and stress corrosion cracking behavior of medium strength Al–Zn–Mg alloy have been investigated by optical microscopy, scanning electron microscopy, electron backscatter diffraction, transmission electron microscopy and slow strain rate test. The results indicate that the addition of Sc results in the formation of the quaternary coherent Al_3(Sc, Zr, Ti) dispersoids during homogenization treatment, which will inhibit the dynamic recrystallization behavior. The number density of Al_3(Sc, Zr, Ti) particles increases with the increase of Sc content, and thus the recrystallization fraction of hot-extruded alloy is reduced and the peak strength in two-stage artificial aging sample is enhanced. At the same time, the wide of precipitation free zone is reduced, and the content of Zn and Mg in grain boundary particles and precipitation free zone is increased with the increase of Sc content. In peak-aged state, the 0.06 wt% Sc added alloy shows the better stress corrosion cracking resistance than the Sc-free alloy because of the reduction of recrystallization fraction and the interrupted distribution of grain boundary precipitates along grain boundary. However, the further addition of Sc to 0.11 wt% will result in the deterioration of stress corrosion cracking resistance due to the increase of electrochemical activity of grain boundary particles and precipitation free zone as well as hydrogen embrittlement. | Zhaoming Li Haichang Jiang Yunli Wang Duo Zhang Desheng Yan Lijian Rong | 2018 | Journal of Materials Science & Technology2018，34，7： | 14 |
| 3 | Angiotensin Ⅱ promotes NO production, inhibits apoptosis and enhances adhesion potential of bone marrow-derived endothelial progenitor cells显示文摘Endothelial 祖先房间(EPC ) 响应织物局部缺血和 endothelial 损害参予出生后的 neovascularization 和 re-endothelialization 的过程。在场的 EPC 的水平被发现了直接与心血管的疾病的结果被联系,并且能被 stimulatory 或禁止的因素调整。给在血管收缩素 II (AngII ) 和心血管的系统之间的靠近的关系,我们在导出的骨头髓(BM ) 的活动调查了 AngII 的效果 EPC。房间被密度坡度 centrifugation 从老鼠的 BM 孤立。AngII 的管理显著地支持了氮的氧化物(没有) 版本,禁止的 EPC apoptosis 和提高的 EPC 粘附潜力。所有被预告的处理与 valsartan 或 L 名字 EPC 上的这些调停 AngII 的效果稀释。而且, LY294002 和 wortmannin 废除了 AngII 的 anti-apoptotic 效果。西方的污点分析显示了没有 synthase (eNOS ) 蛋白质和 phosphorylated Akt 在 EPC 与 AngII 的处理增加了的那 endothelial。因此, AngII 通过 AngII 类型 1 受体(AT1R ) 改进了 EPC 的几项活动,它可以代表与 angiogenesis 连接 AngII 和 AT1R 的可能的机制。另外,导致 AngII 通过在 EPC 的 eNOS 的合成都不调整 apoptosis 和粘附,并且 PI3-kinase/Akt 小径在导致 AngII 的 antiapoptosis 发信号有一个必要角色。 | Tao Yin Xinliang Ma Li Zhao Kang Cheng Haichang Wang | 2008 | Cell Research2008，18，7： | 12 |
| 4 | Nine-month angiographic and two-year clinical follow-up of polymer-free sirolimus-eluting stent versus durable-polymer sirolimus-eluting stent for coronary artery disease: the Nano randomized trial显示文摘 | Zhang Yaojun Chen Fang Takashi Muramatsu Xu Bo Li Zhanquan Ge Junbo He Qing Yang Zhijian Li Shumei Wang Lefeng Wang Haichang He Ben Li Kang Qi Guoxian Li Tianchang Zeng Hesong Peng Jianjun Jiang Tieming Zeng Qiutang Zhu Jianhua Fu Guosheng Christos V. Bourantas Patrick W. Serruys Huo Yong | 2014 | Chinese Medical Journal2014，，11： | 8 |
| 5 | Recent advances on 3D printing graphene-based composites显示文摘3D printing or additive manufacturing (AM) has revolutionized the way of manufacturing by designing complex structures in a customized feature which cannot be realized by traditional processing methods. Incoming materials are trying to adopt 3D printing techniques which directly fabricate sophisticated entities with multifunctionality like mechanical, electrical, thermal and magnetic properties etc. For the realization of advanced materials, 3D printing techniques are emerging from single material to composite materials manufacturing by simply introducing the nano- and micro-reinforcements with the matrix. In this review, we provide an outline of 3D printing graphene-based composites according to various AM techniques including fused deposition modeling (FDM), direct ink writing (DIW), stereolithography (SLA) and selective laser sintering (SLS). First a brief introduction of various AM techniques is given to get a basic understanding of the principles of 3D printing, and then the fabrication process, structural characteristics and applications of different 3D printing techniques for graphene-based composites are summarized. In addition, some effective simulation and characterization methods are also included. We hope that this review would clarify the potential of AM techniques for composite materials and can open new prospects for designing of novel materials. | Haichang Guo Ruicong Lv Shulin Bai | 2019 | Nano Materials Science2019，1，2： | 6 |
| 6 | Collaborative filtering recommendation algorithm based on interactive data classification显示文摘In the matrix factorization(MF)based collaborative filtering recommendation method,the most critical part is to deal with the interaction between the features of users and items.The mainstream approach is to use the inner product for MF to describe the user-item relationship.However,as a shallow model,MF has its limitations in describing the relationship between data.In addition,when the size of the data is large,the performance of MF is often poor due to data sparsity and noise.This paper presents a model called PIDC,short for potential interaction data clustering based deep learning recommendation.First,it uses classifiers to filter and cluster recommended items to solve the problem of sparse training data.Second,it combines MF and multi-layer perceptron(MLP)to optimize the prediction effect,and the limitation of inner product on the model expression ability is eliminated.The proposed model PIDC is tested on two datasets.The experimental results show that compared with the existing benchmark algorithm,the model improved the recommendation effect. | Ji Yimu Li Ke Liu Shangdong Liu Qiang Yao Haichang Li Kui | 2020 | The Journal of China Universities of Posts and Telecommunications2020，27，5： | 4 |
| 7 | Immobilization of insulin-like growth factor-1 onto thermosensitive hydrogels to enhance cardiac progenitor cell survival and differentiation under ischemic conditions显示文摘Stem cell therapy is a promising approach to treat myocardial infarction. However, direct delivery of stem cells into hearts experiences poor cell engraftment and differentiation, due to ischemic conditions(low nutrient and oxygen) in the infarct hearts. Development of suitable cell carriers capable of supporting cell survival and differentiation under these harsh conditions is critical for improving the efficacy of current stem cell therapy. In this work, we created a family of novel cell carriers based on thermosensitive hydrogels and insulin-like growth factor 1(IGF-1), and investigated if these cell carriers can improve cell survival and differentiation under ischemic conditions. The thermosensitive hydrogels were synthesized from N-isopropylacryla- mide, acrylic acid, acrylic acid N-hydroxysuccinicimide ester, and 2-hydroxyethyl methacrylate-oligo(hydroxybutyrate). The hydrogel solutions can be readily injected through 26G needles, and can quickly solidify at 37 oC to form highly flexible hydrogels. IGF-1 was immobilized into the hydrogels in order to support long-term cell survival and differentiation. Different amount of IGF-1 was immobilized by using hydrogels with different content of N-hydroxysuccinicimide ester groups. Cardiosphere derived cells were encapsulated in the hydrogels and cultured under ischemic conditions. The results demonstrated that a significant improvement of cell survival and differentiation was achieved after IGF-1 immobilization. These IGF-1 immobilized hydrogels have the potential to improve cell survival and differentiation in infarct hearts. | LI ZhenQing XU YanYi LI HaiChang GUAN JianJun | 2014 | Science China Chemistry2014，57，4： | 3 |
| 8 | Enhancing through-plane thermal conductivity of fluoropolymer composite by developing in situ nano-urethane linkage at graphene–graphene interface显示文摘Attributed to the intense development and complexity in electronic devices,energy dissipation is becoming more essential nowadays.The carbonaceous materials particularly graphene(Gr)-based thermal interface materials(TIMs)are exceptional in heat management.However,because of the anisotropic behavior of Gr in composites,the TIMs having outstanding through-plane thermal conductivity(┴TC)are needed to fulfill the upcoming innovation in numerous devices.In order to achieve this,herein,nano-urethane linkage-based modified Gr and carbon fibers architecture termed as nanourethane linkage(NUL)-Gr/carbon fibers(CFs)is fabricated.Wherein,toluene diisocyanate is utilized to develop a novel but simple NUL to shape a new interface between graphene sheets.Interestingly,the prepared composite of NUL-Gr/CFs with polyvinylidene fluoride matrix shows outstanding performance in heat management.Owing to the unique structure of NUL-Gr/CFs,an unprecedented value of┴TC(~7.96 W·m^–1·K^–1)is achieved at a low filler fraction of 13.8 wt.%which translates into an improvement of^3,980%of pristine polymer.The achieved outcomes elucidate the significance of the covalent interaction between graphene sheets as well as strong bonding among graphene and matrix in the composites and manifest the potential of proposed NUL-Gr/CFs architecture for practical applications. | Muhammad Maqbool Haichang Guo Akbar Bashir Ali Usman Adeel YAbid Guansong He Yanjuan Ren Zeeshan Ali Shulin Bai | 2020 | Nano Research2020，13，10： | 3 |
| 9 | Wind turbine blade health monitoring with piezoceramic-based wireless sensor network显示文摘In this paper,a piezoceramic-based wireless sensor network(WSN)was developed for health monitoring of wind turbine blades with active sensing approach.The WSN system has an access point that coordinates the network and connects to a PC to control the wireless nodes.One wireless node functions as an actuator to excite an embedded piezoceramic patch with desired guided waves.The remaining wireless nodes function as sensors to detect and transmit the wave responses at distributed locations.The damage status inside the blade was evaluated through the analysis of the sensor signals.Based on wavelet packet analysis results,a damage index and a damage matrix were developed to evaluate the damage status at different locations.To verify the effectiveness of the proposed approach,a static loading test and a wind tunnel test were performed in the Laboratory of Joint Wind Tunnel and Wave Flume at Harbin Institute of Technology(HIT),China.Experimental results show that damage in wind turbine blades can be detected and evaluated by the proposed approach. | Gangbing Song Hui Li Bosko Gajic Wensong Zhou Peng Chen Haichang Gu | 2013 | International Journal of Smart and Nano Materials2013，4，3： | 3 |
| 10 | Microstructure and Mechanical Properties of a CuCrZr Welding Joint After Continuous Extrusion显示文摘The effect of continuous extrusion forming(CEF) process on the microstructure and mechanical properties of a CuCrZr welding joint was investigated. The experimental results showed that after the CEF process the grains were refined to submicron-scale through dynamic recrystallization,which improved the mechanical properties of the welding joint as well as the base material. Meanwhile,the micron-scale precipitates aggregated at the grain boundaries in the welding process were broken down to smaller ones and recrystallized grains of several micrometers formed around the precipitates after CEF process,which could alleviate the negative effect induced by the micron-scale precipitates during plastic deforming process. Finer grains and smaller micronscale precipitates made contributions to improve the properties of a CuCrZr alloy with a welding joint. | Hui Feng Haichang Jiang Desheng Yan Lijian Rong | 2015 | Journal of Materials Science & Technology2015，31，2： | 3 |
| 11 | A Novel TiNi/AlSi Composite with High Strength and High Damping Capacity显示文摘A novel TiNi/AlSi composite with high compressive strength and high damping capacity was obtained by infiltrating Al-12%Si alloy into porous TiNi alloy.It had been found that the high compressive strength (440 MPa) of TiNi/AlSi composite is due to the increase of effective carrying area after infiltrating Al-12%Si alloy,while the high damping capacity is contributed to TiNi carcass,Al-12%Si filling material and micro- slipping at the interface. | Shuwei LIU Xiuyan LI Desheng YAN Haichang JIANG Lijian RONG | 2008 | Journal of Materials Science & Technology2008，24，6： | 3 |
| 12 | Role ofδ-ferrite in fatigue crack growth of AISI 316 austenitic stainless steel显示文摘FF sample(nearly free ofδ-ferrite)and CF sample(containing∼4%δ-ferrite)were prepared from the AISI 316 austenitic stainless steel plate to elucidate the role ofδ-ferrite in the fatigue crack growth under the solution treated and accelerated aged conditions.It is found that the fatigue crack growth resistance of the CF sample is higher than the FF sample under the solution treated condition.However,a significant deterioration of the fatigue crack growth resistance is observed in the CF sample while little variation is found in the FF sample after accelerated aging treatment at 750°C for 10 h.In the solution treated condition,deflected crack growth path is present when the main crack encounters theδ-ferrite in the CF sample due to the differences in the fatigue responses between austenite andδ-ferrite.The measured growth rate of the deflected crack is significantly slower than that of the flat crack of the same length.After the accelerated aging treatment,microcracks are produced at the M_(23)C_(6)/δinterface due to the strain incompatibility between M_(23)C_(6) and retainedδ-ferrite when the decomposedδ-ferrite is subject to plastic deformation in the crack tip plastic zone.The preexisting microcracks in the front of crack tip provide a viable path for crack propagation,resulting in the relatively flat crack path. | Qiyu Wang Shenghu Chen Xinliang Lv Haichang Jiang Lijian Rong | 2022 | Journal of Materials Science & Technology2022，，19： | 3 |
| 13 | 利用压电陶瓷作动器对柔性悬臂梁正位反馈控制试验显示文摘目的验证压电陶瓷智能传感器和驱动器以及正位反馈控制对柔性结构主动控制的有效性.方法将压电陶瓷片分别作为传感器和作动器使用,并粘贴于铝制悬臂梁的表面,对其振动反应实施实时控制.试验过程分为2个阶段,第1阶段5 s为启振阶段,通过激励压电陶瓷作动器使结构产生振动;第2阶段为控制阶段.利用压电陶瓷传感器得到的反馈信号,通过正位反馈算法计算出控制信号.驱动压电陶瓷作动器对结构的振动响应进行实时控制.结果试验得到了模态振动控制与瞬时脉冲振动控制的振动响应曲线,并分别对有控与无控情况进行对比.结论试验结果证明利用压电陶瓷以及正位反馈控制算法能够有效抑制外界激励下的一阶、二阶模态振动和瞬时脉冲扰动引起的结构振动. | 阎石 张皓 Gangbing SONG Haichang GU | 2008 | 沈阳建筑大学学报(自然科学版)2008，24，3： | 2 |
| 14 | Damping behavior of Ti_(50.1)Ni_(49.9) alloy in reverse martensitic transformation region显示文摘Damping behavior of Ti50.1Ni49.9 shape memory alloy during reverse martensitic transformation has been investigated by dynamic mechanical analyzer in a dual-cantilever mode.With the increase of strain amplitude,internal friction(IF) of the alloy increases in martensite and austenite states while decreases in transformation region.Based on the regularity of IF attenuation in isothermal condition,IFTr and(IFPT+ IFI) are decomposed from the strain amplitude dependent IF in transformation region.For practical application of shape memory alloys as a damping material,it is significant to evaluate the damping capacity by eliminating the influence of IFTr and consider its time independent real IF(IFPT+ IFI). | ZENG JianMin JIANG HaiChang LIU ShuWei RONG LiJian | 2012 | Science China(Technological Sciences)2012，55，2： | 2 |
| 15 | Vertical Alignment of Anisotropic Fillers Assisted by Expansion Flow in Polymer Composites显示文摘Orientation control of anisotropic one-dimensional(1D)and two-dimensional(2D)materials in solutions is of great importance in many fields ranging from structural materials design,the thermal management,to energy storage.Achieving fine control of vertical alignment of anisotropic fillers(such as graphene,boron nitride(BN),and carbon fiber)remains challenging.This work presents a universal and scalable method for constructing vertically aligned structures of anisotropic fillers in composites assisted by the expansion flow(using2D BN platelets as a proof-of-concept).BN platelets in the silicone gel strip are oriented in a curved shape that includes vertical alignment in the central area and horizontal alignment close to strip surfaces.Due to the vertical orientation of BN in the central area of strips,a throughplane thermal conductivity as high as 5.65 W m^(-1) K^(-1) was obtained,which can be further improved to 6.54 W m^(-1) K^(-1) by combining BN and pitch-based carbon fibers.The expansion-flow-assisted alignment can be extended to the manufacture of a variety of polymer composites filled with 1D and 2D materials,which can find wide applications in batteries,electronics,and energy storage devices. | Hongyu Niu Haichang Guo Lei Kang Liucheng Ren Ruicong Lv Shulin Bai | 2022 | Nano-Micro Letters2022，14，9： | 2 |
| 16 | Sustained delivery of rhMG53 promotes diabetic wound healing and hair follicle development显示文摘MG53 is an essential component of the cell membrane repair machinery,participating in the healing of dermal wounds.Here we develop a novel delivery system using recombinant human MG53(rhMG53)protein and a reactive oxygen species(ROS)-scavenging gel to treat diabetic wounds.Mice with ablation of MG53 display defective hair follicle structure,and topical application of rhMG53 can promote hair growth in the mg53/mice.Cell lineage tracing studies reveal a physiological function of MG53 in modulating the proliferation of hair follicle stem cells(HFSCs).We find that rhMG53 protects HFSCs from oxidative stress-induced apoptosis and stimulates differentiation of HSFCs into keratinocytes.The cytoprotective function of MG53 is mediated by STATs and MAPK signaling in HFSCs.The thermosensitive ROS-scavenging gel encapsulated with rhMG53 allows for sustained release of rhMG53 and promotes healing of chronic cutaneous wounds and hair follicle development in the db/db mice.These findings support the potential therapeutic value of using rhMG53 in combination with ROS-scavenging gel to treat diabetic wounds. | Hong Niu Haichang Li Ya Guan Xin Zhou Zhongguang Li Serana Li Zhao Peng Chen Tao Tan Hua Zhu Valerie Bergdall Xuehong Xu Jianjie Ma Jianjun Guan | 2022 | Bioactive Materials2022，7，12： | 2 |
| 17 | Robust coded MIMO FH - CDMA transceiver for mobile Ad Hoc networks 显示文摘 | Sui Haichang Zeidler J R | 2007 | IEEE Journal on Selected Areas in Communications2007，25，7： | 1 |
| 18 | Smart aggregate based damage detection of circular RC columns under cyclic combinedloading显示文摘 | Yashar Moslehy Haichang Gu Abdeldjelil Belarbi Y L Mo Gangbing Song | 2010 | Smart Materials and Structures2010，，6： | 1 |
| 19 | Multi-functional smart aggregate-based structural health monitoring of circular reinforcedconcrete columns subjected to seismic excitations显示文摘 | Haichang Gu Yashar Moslehy David Sanders Gangbing Song Y L Mo | 2010 | Smart Materials and Structures2010，，6： | 1 |
| 20 | Progressive collapse of a two-story reinforced concrete frame with embedded smartaggregates显示文摘 | Arghadeep Laskar Haichang Gu Y L Mo Gangbing Song | 2009 | Smart Materials and Structures2009，，7： | 1 |
您所在的机构暂未开通此部分的功能，请联系管理员