维普中文期刊产品整合服务
19篇 您的检索式:作者名="Chen Ruipeng"
    题名 作者 年代 出处 被引量
1World-class Xincheng gold deposit: An example from the giant Jiaodong gold province显示文摘The Jiaodong gold deposits are currently the most important gold resources(with Au reserves of>4000 t) in China,and the leading gold-producing country globally(with Au production of ~428 t in2013).Jiaodong is also considered as perhaps the only world-class to giant gold accumulation on the planet where relatively young gold ores(ca.130-120 Ma) were deposited in rocks that are 2 Ga older.The Xincheng world-class high-grade gold deposit,with a proven reserve of >200 t gold,is one of the largest deposits in the giant gold province of the Jiaodong Peninsula.It is located in the northwestern part of the jiaobei Uplift,and hosted by ca.132-123 Ma Xincheng quartz monzonites and monzogranites.Ore zones are structurally controlled by the NE-trending and NW-dipping Jiaojia Fault and subsidiary faults,and are mainly restricted to the footwall of the fault.The dominant disseminated- and stockworkstyle ores are associated with strong sericitization,silicification,sulfidation and K-feldspathization,and minor carbonate wallrock alteration halos.The four mineralization stages are pyrite-quartz-sericite(stage 1),quartz-pyrite(stage 2),quartz-polysulfide(stage 3) and quartz-carbonate(stage 4).Gold occurs dominantly as electrum,with lesser amounts of sulfide-hosted native gold and rare native silver and argentite,normally associated with pyrite,chalcopyrite,galena and sphalerite:the latter with proven resources of about 105 t Ag,713 t Cu,and 5100 t S.There are three types of ore-related fluid inclusions:type 1 aqueous-carbonate(H_2O-CO_2),type 2aqueous(liquid H_2O+vapor H_2O),and type 3 CO_2(liquid CO_2 and vapor CO_2) inclusions.Homogenization temperatures range from 221 to 304℃ for type 1 inclusions,with salinities of 2.4-13.3 wt.%NaCl eq.,and bulk densities of 0.858-1.022 g/cm^3.The δ^(34)S_(CDT) values of hydrothermal sulfides are 4.3-10.6‰and δ^(18)O values of hydrothermal quartz have a median value of 13.0‰.δD values of fluid inclusions in hydrothermal quartz have a median value of-75‰.Calculated δ^(18)Owater has a median value of 5.2‰.The timing of gold mineralization at the Xincheng gold deposit is younger than 123±1 Ma,and likely between 120.9 and 119.9 Ma.A minerals system genetic model for the probable epizonal orogenic Xincheng deposit suggests an initial medium temperature,CO_2-rich,and low salinity H_2O-CO_2 deeply sourced metamorphic ore fluid associated with dehydration and decarbonization of subducting Paleo-Pacific lithosphere.The Jiaojia Fault constrained the migration of ore-forming fluids and metals at the brittle-ductile transition.Fluid immiscibility,caused by episodic pressure drops,led to significant high-grade gold deposition in the giant Xincheng gold deposit.Liqiang Yang Jun Deng Ruipeng Guo Lin'nan Guo Zhongliang Wang Binghan Chen XudongWang 2016Geoscience Frontiers2016,7,3:14
2Evaluation of the Biodiversity Conservation Function in Liaohe Delta Wetland,Northeastern China显示文摘The scientific evaluation of the wetland biodiversity conservation function is the basis of balanced wetland protection and development. Our research sought to provide references for the protection of wetland ecological environments as well as the related planning and management policies. The study established a fitting model for evaluating the biodiversity conservation function in the Liaohe Delta, northeastern China. The new model, the Wetland Biodiversity Conservation Indicator(WBCI), was with four input factors, including the vegetation coverage(VC), habitat suitability index(HI), land use and land cover(LULC) index(LI), and threat factor index(TI) of the LULC type. The values assigned to HI and TI were based on Integrated Valuation of Ecosystem Services and Tradeoffs(In VEST)habitat quality models. The weights of all the factors in WBCI were valued with the Principal Component Analysis(PCA). We evaluated the wetland biodiversity conservation function of Panjin, Liaohe Delta, China, by using the WBCI model based on Gaofen-1(GF-1) satellite data in 2018, and the result was verified with In VEST and other models. It showed that the output map was similar to that of In VEST, with the higher-quality habitat including the wetland, tidal flat, water body, and forest, as well as the lower-quality land use types including the paddy field, crop field, construction land, and land used by traffic. The wetland biodiversity conservation function was better in areas less affected by human disturbance, with very abundant species and good-quality habitat. It was poor in areas impacted by more frequent human activities such as the land cultivation, housing, and traffic, which led to the landscape fragmentation. The WBCI model provided a more accurate reflection of the bird distribution than the In VEST model. The WBCI model was able to reflect the difference in quality of each habitat grade, in contrast to the net primary productivity(NPP) method and species distribution models(SDMs). The new model was, therefore, simpler and suitable in reflecting the quality of wetland biodiversity function in the Liaohe Delta.Wenying YU Ruipeng JI Xiuzhen HAN Long CHEN Rui FENG Jinwen WU Yushu ZHANG 2020Journal of Meteorological Research2020,34,4:4
3Effect of potential HONO sources on peroxyacetyl nitrate(PAN)formation in eastern China in winter显示文摘As an important secondary photochemical pollutant,peroxyacetyl nitrate(PAN)has been studied over decades,yet its simulations usually underestimate the corresponding observations,especially in polluted areas.Recent observations in north China found unusually high concentrations of PAN during wintertime heavy haze events,but the current model still cannot reproduce the observations,and researchers speculated that nitrous acid(HONO)played a key role in PAN formation.For the first time we systematically assessed the impact of potential HONO sources on PAN formation mechanisms in eastern China using the Weather Research and Forecasting/Chemistry(WRF-Chem)model in February of 2017.The results showed that the potential HONO sources significantly improved the PAN simulations,remarkably accelerated the RO x(sum of hydroxyl,hydroperoxyl,and organic peroxy radicals)cycles,and resulted in 80%–150%enhancements of PAN near the ground in the coastal areas of eastern China and 10%–50%enhancements in the areas around 35–40°N within 3 km during a heavy haze period.The direct precursors of PAN were aldehyde and methylglyoxal,and the primary precursors of PAN were alkenes with C>3,xylenes,propene and toluene.The above results suggest that the potential HONO sources should be considered in regional and global chemical transport models when conducting PAN studies.Jingwei Zhang Yitian Guo Yu Qu Yong Chen Ruipeng Yu Chaoyang Xue Rui Yang Qiang Zhang Xingang Liu Yujing Mu Jing Wang Can Ye Haihan Zhao Qiangqiang Sun Ziwen Wang Junling An 2020Journal of Environmental Sciences2020,32,8:3
4Cooperative effect from cation and anion of pyridine-containing anion-based ionic liquids for catalysing CO_2 transformation at ambient conditions显示文摘Pyridine-containing anion-based ionic liquids(PA-ILs) with two kinds of interaction sites to bind CO_2, e.g., [P4444][2-OP], were found to be highly efficient for catalysing the cycloaddition reactions of atmospheric CO_2 with epoxides at room temperature under metal-and halogen-free conditions, producing a series of cyclic carbonates in high yields. It was demonstrated that the cooperative interaction from two interaction sites in the anions of PA-ILs activated CO_2, while the cation activated the epoxides substrates via coordination to the central P+ unit, thus resulting in the high activity of the IL catalysts.Guangfeng Yuan Yanfei Zhao Yunyan Wu Ruipeng Li Yu Chen Dongmei Xu Zhimin Liu 2017Science China Chemistry2017,60,7:2
5Mechanism of hydrogen desorption during palladium brush plating 显示文摘Ruipeng Yang Xun Cai Qinglong Chen 2001Surface & Coating Technology2001,141,:1
6Positive Periodic Solutions of Second-Order Singular Coupled Systems with Damping Terms显示文摘We establish the existence of positive periodic solutions of the second-order singular coupled systems{x′′+ p_1(t)x′+ q_1(t)x = f_1(t, y(t)) + c_1(t),y′′+ p_2(t)y′+ q_2(t)y = f_2(t, x(t)) + c_2(t),where pi, qi, ci ∈ C(R/T Z; R), i = 1, 2; f_1, f_2 ∈ C(R/T Z ×(0, ∞), R) and may be singular near the zero. The proof relies on Schauder's fixed point theorem and anti-maximum principle.Our main results generalize and improve those available in the literature.Ruipeng CHEN Xiaoya LI 2017Journal of Mathematical Research with Applications2017,37,4:1
7Reasonable location of stopping line in close‑distance underlying coal seam and partition support of large cross‑section roadway显示文摘Close-distance coal seams are widely distributed over China,and the coal pillars left by the overlying coal seams afect the retracement channel of the underlying coal seam in the stopping stage.Based on the engineering background of close-distance seam mining in a coal mine,the reasonable position of the underlying coal seam's stopping line and the support method of the large section roadway during stopping are investigated using feld measurements,similar simulation experiments,and numerical simulations.There are three types of location relationships between the stopping line of the underlying coal seam and the stopping line of the overlying coal seam:'externally staggered with the upper stopping line'(ESUL,stops mining under the overlying goaf),'overlapped with upper stopping line'(OUL),and'internally staggered with the upper stopping line'(ISUL,ISUL-SD for shorter internal staggered distances,ISUL-LD for longer ones).There are diferent stress arch structures in the overlying strata of the above three positions,and the stress arch evolution process exists in the process of ESUL→OUL→ISUL-SD→ISUL-LD:a front and rear double stress arch structure→the front arch gradually decreases→the front arch dies out,and the double arch synthesizes the single arch→the single-arch range expands→the nested double arch.The relationship between the stress arch structure and the position of the stopping line is evaluated as follows:(1)ESUL:the stress concentration in the roof plate of the retracement channel of the underlying coal seam is the highest,because the overburden block of the extensive collapse zone acts directly on the roof plate of the retracement channel,resulting in relative difculties in roof support.(2)OUL:although the retracement channel roof pressure is minimal,the overlying rock structure has the potential for rotation or slippage instability.(3)ISUL-SD:the pressure on the roof of the retracement channel is small and the overburden structure is stable,which is conducive to the safe retraction of the support and not limited by the width of the end-mining coal pillar.(4)ISUL-LD:it is basically the same as the condition of stopping under the non-goaf;however,it has a limitation on the width of the end-mining coal pillar.The location of the stopping line is selected as ISUL-SD,and the retraction process of the self-excavating retraction channel was adopted.A partition asymmetric support scheme which is proven by feld practice is proposed,through a comprehensive analysis of the pre-stress feld simulation of the support scheme,based on the diferent control requirements of the roof above the support and the roof of the retracement channel in the stopping area.This method realizes safe and smooth withdrawal of the support.Dongdong Chen Yiyi Wu Shengrong Xie Fangfang Guo Fulian He Ruipeng Liu 2022International Journal of Coal Science & Technology2022,9,4:1
8Positive periodic solutions of second-order differential equations with weak singularities显示文摘MA Ruyun CHEN Ruipeng HE Zhiqian 2014Applied Mathematics and Computation2014,232,:1
9Perovskite Solar Cells toward Eco-Friendly Printing显示文摘Eco-friendly printing is important for mass manufacturing of thin-film photovoltaic(PV)devices to preserve human safety and the environment and to reduce energy consumption and capital expense.However,it is challenging for perovskite PVs due to the lack of eco-friendly solvents for ambient fast printing.In this study,we demonstrate for the first time an eco-friendly printing concept for high-performance perovskite solar cells.Both the perovskite and charge transport layers were fabricated from eco-friendly solvents via scalable fast blade coating under ambient conditions.The perovskite dynamic crystallization during blade coating investigated using in situ grazing incidence wide-angle X-ray scattering(GIWAXS)reveals a long sol-gel window prior to phase transformation and a strong interaction between the precursors and the eco-friendly solvents.The insights enable the achievement of high quality coatings for both the perovskite and charge transport layers by controlling film formation during scalable coating.The excellent optoelectronic properties of these coatings translate to a power conversion efficiency of 18.26%for eco-friendly printed solar cells,which is on par with the conventional devices fabricated via spin coating from toxic solvents under inert atmosphere.The eco-friendly printing paradigm presented in this work paves the way for future green and highthroughput fabrication on an industrial scale for perovskite PVs.Xiaoming Chang Yuanyuan Fan Kui Zhao Junjie Fang Dongle Liu Ming-Chun Tang Dounya Barrit Detlef-MSmilgies Ruipeng Li Jing Lu Jianbo Li Tinghuan Yang Aram Amassian Zicheng Ding Yonghua Chen Shengzhong(Frank)Liu Wei Huang 2021Research2021,,1:1
10Existence of positive periodic solutions of nonlinear first-order delayed differ- ential equations 显示文摘Ma Ruyun Chen Ruipeng Chen Tianlan 2011Journal of Mathematical Analysis and Ap- plications2011,384,:1
11Failure analysis and control technology of intersections of large‑scale variable cross‑section roadways in deep soft rock显示文摘In deep underground mining,achieving stable support for roadways along with long service life is critical and the complex geological environment at such depths frequently presents a major challenge.Owing to the coupling action of multiple factors such as deep high stress,adjacent faults,cross-layer design,weak lithology,broken surrounding rock,variable cross-sections,wide sections up to 9.9 m,and clusters of nearby chambers,there was severe deformation and breakdown in the No.10 intersection of the roadway of large-scale variable cross-section at the−760 m level in a coal mine.As there are insufcient examples in engineering methods pertaining to the geological environment described above,the numerical calculation model was oversimplifed and support theory underdeveloped;therefore,it is imperative to develop an efective support system for the stability and sustenance of deep roadways.In this study,a quantitative analysis of the geological environment of the roadway through feld observations,borehole-scoping,and ground stress testing is carried out to establish the FLAC 3D variable cross-section crossing roadway model.This model is combined with the strain softening constitutive(surrounding rock)and Mohr–Coulomb constitutive(other deep rock formations)models to construct a compression arch mechanical model for deep soft rock,based on the quadratic parabolic Mohr criterion.An integrated control technology of bolting and grouting that is mainly composed of a high-strength hollow grouting cable bolt equipped with modifed cement grouting materials and a high-elongation cable bolt is developed by analyzing the strengthening properties of the surrounding rock before and after bolting,based on the Heok-Brown criterion.As a result of on-site practice,the following conclusions are drawn:(1)The plastic zone of the roof of the cross roadway is approximately 6 m deep in this environment,the tectonic stress is nearly 30 MPa,and the surrounding rock is severely fractured.(2)The deformation of the roadway progressively increases from small to large cross-sections,almost doubling at the largest cross-section.The plastic zone is concentrated at the top plate and shoulder and decreases progressively from the two sides to the bottom corner.The range of stress concentration at the sides of the intersection roadway close to the passageway is wider and higher.(3)The 7 m-thick reinforced compression arch constructed under the strengthening support scheme has a bearing capacity enhanced by 1.8 to 2.3 times and increase in thickness of the bearing structure by 1.76 times as compared to the original scheme.(4)The increase in the mechanical parameters c andφof the surrounding rock after anchoring causes a signifcant increase inσt;the pulling force of the cable bolt beneath the new grouting material is more than twice that of ordinary cement grout,and according to the test,the supporting stress feld shows that the 7.24 m surrounding rock is compacted and strengthened in addition to providing a strong foundation for the bolt(cable).On-site monitoring shows that the 60-days convergence is less than 30 mm,indicating that the stability control of the roadway is successful.Shengrong Xie Yiyi Wu Dongdong Chen Ruipeng Liu Xintao Han Qiucheng Ye 2022International Journal of Coal Science & Technology2022,9,2:1
12Renal cell carcinoma associated with Xp11.2 translocation/ TFE3 gene fusions: clinical experience and literature review显示文摘Jian He Xiancheng Chen Weidong Gan Bin Zhu Xiangshan Fan Hongqian Guo Ruipeng Jia 2015Future Oncol2015,,0:1
13Mechanism of Hydrogen desorption during palladium brush plating显示文摘Ruipeng Yang Xun Cai Qinglong Chen 2001Surface & Coating Technology2001,141,:1
14Existence of positive periodic solutions of nonlinear first-order delayed differ- ential equations显示文摘Ma Ruyun Chen Ruipeng Chen Tianlan 2011J Math Anal Appl2011,384,:1
15Existence of positive periodic solutions of nonlinear first order delayed differen- tial equations显示文摘MA Ruyun CHEN Ruipeng CHEN Tianlan 2011J Math Anal Appl2011,384,2:1
16组蛋白脱甲基酶LSD1通过抑制Wnt信号传导促进脂肪细胞分化显示文摘脂肪组织对于动物的生理活动至关重要。白色脂肪的主要作用是储存能量,而棕色脂肪通过UCP1-介导的能量消耗过程调控非颤抖性产热。虽然我们对表观遗传学机制在多种分化过程中的调节作用有所认识,但对于棕色脂肪细胞分化的表观遗传调控了解甚少。Yan Chen Jeesun Kim Ruipeng Zhang Xiaoqin Yang Yong Zhang Jianwu Fang Zhui Chen Lin Teng Xiaowei Chen Hui Ge Peter Atadja En Li Taiping Chen 戚炜 2017科学新闻2017,19,4:0
17Effect of annealing temperature on magnetic properties of a sintered Nd-Fe-B magnet after grain boundary diffusion with Dy_(70)Cu_(30) alloy显示文摘Grain boundary diffusion process(GBDP)has been developed as an effective approach to increase the coercivity of sintered Nd-Fe-B magnets by regulating the compositions and phase distributions near grain boundaries.This work aims to explore how to select the optimum annealing temperature after GBDP.In this work GBDP was performed on a sintered Nd-Fe-B magnet using Dy_(70)Cu_(30) alloy.After GBDP the low eutectic temperature of the grain boundary phases decreases from the initial 492 to 451℃.The magnetic property dependent on different annealing temperatures near the low eutectic temperature was studied.The magnetic properties,especially the squareness factor of demagnetization curve show a strong dependence on the annealing temperature.After GBDP the optimal magnetic properties can be obtained after annealing just above the low eutectic temperature of the grain boundary phases.The mechanism is discussed based on the microstructure analysis.Ruipeng Qian Yuxuan Ma Fugang Chen Hui Sun Yong Zhao Yunlong Chen 2024Journal of Rare Earths2024,42,1:0
18EXISTENCE AND MULTIPLICITY OF POSITIVE SOLUTIONS TO NONLINEAR SEMIPOSITONE NEUMANN BOUNDARY VALUE PROBLEM显示文摘In this paper, we study a nonlinear semipositone Neumann boundary value problem. Under some suitable conditions, we prove the existence and multiplicity of positive solutions to the problem, based on Krasnosel'skii's fixed point theorem in cones.Ruipeng Chen , Yanqiong Lu (Dept. of Math., Northwest Normal University, Lanzhou 730070) 2012Annals of Differential Equations2012,28,2:0
19POSITIVE PERIODIC SOLUTIONS OF THE FIRST-ORDER SINGULAR DISCRETE SYSTEMS显示文摘In this paper, we study two kinds of first-order singular discrete systems.By the fixed point index theory, we investigate the existence and multiplicity of positive periodic solutions of the systems.Ruipeng Chen Xiaoya Li 2018Annals of Applied Mathematics2018,34,1:0
返回顶部 每页显示:
共1页 首页 上一页 第1页 下一页 末页 /1 跳转

网站首页 | 关于我们 | 联系我们 | 产品服务 | 客服中心 | 广告服务 | 版权声明 | 网站联盟 | 友情链接 | 售卡网点

版权所有© 渝B2-20050021-1 渝公网安备 50019002500403号 违法和不良信息举报中心

互联网出版许可证 新出网证(渝)字10号 全国400电话 - 免长途话费