共被期刊论文引用了2次
您的检索式：您选中1篇文献正在查看引证文献汇总
|
|
|
题名
|
作者
|
年代
|
出处
|
被引量
|
| 1 | Analysis of hydro-mechanical processes in a ventilated tunnel in an argillaceous rock on the basis of different modelling approaches显示文摘In this paper, a modelling benchmark exercise from the DECOVALEX-2011 project is presented. The bench-mark is based on the performance and results of a laboratory drying test and of the ventilation experiment (VE) carried out in the Mont Terri Underground Rock Laboratory (URL). Both tests involve Opalinus clay. The work aims at the identification, understanding and quantification of mechanisms taking place during the ventilation of a gallery in argillaceous host rocks on one hand and at investigating the capacity of different codes and individuals to reproduce these processes on the other hand. The 4-year in situ VE took place in a 1.3 m diameter unlined tunnel and included two resaturation-desaturation cycles. The test area was equipped with over one hundred sensors (including the global water mass balance of the system, relative humidity (RH), water content, liquid pressure, relative displacement and concentration of some chemical species) to monitor the rock behaviour during ventilation. The laboratory drying experiment, carried out before the VE, was designed to mimic the in situ conditions. The work was organized in a progressive manner in terms of complexity of the computations to be performed, geared towards the full hydro-mechano-chemical (HMC) understanding of the VE, the final objective. The main results from the modelling work reported herein are that the response of the host rock to ventilation in argillaceous rocks is mainly governed by hydraulic processes (advective Darcy flow and non-advective vapour diffusion) and that the hydro-mechanical (TM) back coupling is weak. A ventilation experiment may thus be regarded as a large scale-long time pump test and it is used to determine the hydraulic conductivity of the rock mass. | B.Garitte A.Bond A.Millard C.Zhang C.Mcdermott S.Nakama A.Gens | 2013 | Journal of Rock Mechanics and Geotechnical Engineering2013，5，1： | 3 |
| 2 | Analysis of drying and saturating natural gypsum samples for mechanical testing显示文摘The stability of underground abandoned gypsum mines is dependent on the gypsum pillar's strength,and most abandoned mines are in a fully saturated condition. Moisture affects the strength of gypsum and is therefore commonly measured when testing rock strength. For most rocks, this is a simple task of weighing the rock's mass before and after oven-heating at a specified temperature and duration. For natural gypsum, however, this is not a straightforward process. Heating natural gypsum can result in dehydration and transformation of gypsum to hemihydrate and anhydrite, thus changing the physical characteristics of the gypsum such as its particle density which in turn affects the moisture content and strength measurements. To prevent transformation when determining the moisture content of gypsum,the American Society for Testing Materials(ASTM) recommends lowering the drying temperature from 110℃ to 60℃ . To investigate the temperature at which gypsum transforms to hemihydrate, we used a helium pycnometer to measure the particle densities of gypsum, hemihydrate and anhydrite. In this research, we suggest that a higher drying temperature of 80℃ can be used for drying gypsum without transforming gypsum to hemihydrate. Further, preparing saturated samples for mechanical testing,which is required in stability analyses of abandoned mines, is challenging due to the dissolution of gypsum when placed in water. To address this problem, we investigated the following methods to saturate gypsum cores taking into account the solubility of gypsum:(1) water immersion,(2) vacuum saturation, and(3) improved vacuum saturation. The research indicates that all the three methods are acceptable but they should be conducted using a saturated gypsum-water solution to minimize dissolution. Further, the research found that the improved vacuum saturation method saturated the test samples within 24 h, while duration of 30 h was required for the other two methods. | Mohammadhossein Sadeghiamirshahidi Stanley J.Vitton | 2019 | Journal of Rock Mechanics and Geotechnical Engineering2019，11，2： | 1 |
您所在的机构暂未开通此部分的功能，请联系管理员