|
|
|
题名
|
作者
|
年代
|
出处
|
被引量
|
| 1 | Effect of processing routes on microstructure and mechanical properties of 2014 Al alloy processed by equal channel angular pressing显示文摘Al-Cu alloy was deformed through equal channel angular pressing(ECAP) by routes A,Ba,Bc and C up to 5 passes.ECAP was done using a 90° die for three different conditions,namely 1) as received,2) solutionised at 768 K for 1 h and 3) solutionised at 768 K for 1 h + aged at 468 K for 5 h.The microstructure,microhardness and tensile strength were studied for all the three conditions and four routes.Significant improvement in hardness(HV 184 after five passes) and strength(602 MPa after three passes) was observed in solutionised and aged 2014 Al alloy deformed through route Bc.Microstructure evolution was reasonably equiaxed in route Bc with aspect ratio of 1.6.Solutionised and aged 2014 Al alloy deformed through route Bc was identified to have better microstructure and mechanical property than the other processing routes and conditions. | P.VENKATACHALAM S.RAMESH KUMAR B.RAVISANKAR V.THOMAS PAUL M.VIJAYALAKSHMI | 2010 | Transactions of Nonferrous Metals Society of China2010，20，10： | 6 |
| 2 | Investigation of dry sliding wear properties of multi-directional forged Mg-Zn alloys显示文摘Effect of multi-directional forging(MDF)on wear properties of Mg-Zn alloys(with 2,4,and 6wt%Zn)is investigated.Dry sliding wear test was performed using pin on disk machine on MDF processed and homogenized samples.Wear behavior of samples was analyzed at loads of ION and 20 N,with sliding distances of 2000m and 4000m,at a sliding velocity of 3m/s.Microstructures of worn samples were observed under scanning electron microscopy(SEM),energy dispersive spectroscopy(EDS),and x-ray diffraction(XRD)and the results were analyzed.Mechanical properties were evaluated using microhardness test.After 5 passes of MDF,the average grain size was found to be 30±4p m,22±3 pm,and 18±3 pm,in Mg-2%Zn,Mg-4%Zn,and Mg-6%Zn alloys,respectively,with significant improvement in hardness in all cases.Wear resistance was improved after MDF processing,as well as,with increment in Zn content in Mg alloy.However,it decreased when the load and the sliding distance increased.Worn surface exhibited ploughing,delamination,plastic deformation,and wear debris along sliding direction,and abrasive wear was found to be the main mechanism. | S.Ramesh Gajanan Anne H.Shivananda Nayaka Sandeep Sahu M.R.Ramesh | 2019 | Journal of Magnesium and Alloys2019，7，3： | 4 |
| 3 | Sonochemical synthesis of nanostructured nickel hydroxide as an electrode material for improved electrochemical energy storage application显示文摘A facile and fast approach for the synthesis of a nanostructured nickel hydroxide(Ni(OH)_2) via sonochemical technique is reported in the present study. The X-ray diffraction results confirmed that the synthesized Ni(OH)_2 was oriented in β-phase of hexagonal brucite structure. The nanostructured Ni(OH)_2 electrode exhibited the maximum specific capacitance of 1256 F/g at a current density of 200 mA/g in 1 M KOH_((aq)). Ni(OH)_2 electrodes exhibited the pseudocapacitive behavior due to the presence of redox reaction. It also exhibited long-term cyclic stability of 85% after 2000 cycles, suggesting that the nanostructured Ni(OH)_2 electrode will play a promising role for high performance supercapacitor application. | Arshid Numan Navaneethan Duraisamy Fatin Saiha Omar Dhanaraj Gopi K.Ramesh S.Ramesh | 2017 | Progress in Natural Science:Materials International2017，27，4： | 2 |
| 4 | Ce_(1-x)Dy_(x-y)Sr_yO_(2-δ)导电体的制备与表征(英文)显示文摘在Ce1-x Dyx-y Sry O2-δ体系中,研究了Dy和Se对总离子电导率的影响。在该体系中,使用麦芽糖和果胶作为有机前驱体,通过改性溶胶-凝胶工艺,在x=0.15,y=0.015,0.03和0.045的条件下,制备不同组分的导电体。采用X射线衍射谱的Rietveld拟合验证了导电体具有空间群Fmm的立方结构。从SEM像可以看到具有明显晶界、相对均匀的晶粒。在150~500°C的温度范围和40 Hz~1 MHz的频率范围内,采用四探针交流阻抗法测量导电体的总离子电导率。与单掺杂的二氧化铈样品相比,Ce0.85Dy0.12Sr0.03O2-δ具有更高的电导率。 | S.RAMESH K.C.JAMES RAJU C.VISHNUVARDHAN REDDY | 2014 | Transactions of Nonferrous Metals Society of China2014，24，2： | 2 |
| 5 | Recognition and classification of paddy leaf diseases using Optimized Deep Neural network with Jaya algorithm显示文摘In the agriculture field,one of the recent research topics is recognition and classification of diseases from the leaf images of a plant.The recognition of agricultural plant diseases by utilizing the image processing techniques will minimize the reliance on the farmers to protect the agricultural products.In this paper,Recognition and Classification of Paddy Leaf Diseases using Optimized Deep Neural Network with Jaya Algorithm is proposed.For the image acquisition the images of rice plant leaves are directly captured from the farm field for normal,bacterial blight,brown spot,sheath rot and blast diseases.In pre-processing,for the background removal the RGB images are converted into HSV images and based on the hue and saturation parts binary images are extracted to split the diseased and non-diseased part.For the segmentation of diseased portion,normal portion and background a clustering method is used.Classification of diseases is carried out by using Optimized Deep Neural Network with Jaya Optimization Algorithm(DNN_JOA).In order to precise the stability of this approach a feedback loop is generated in the post processing step.The experimental results are evaluated and compared with ANN,DAE and DNN.The proposed method achieved high accuracy of 98.9%for the blast affected,95.78%for the bacterial blight,92%for the sheath rot,94%for the brown spot and 90.57%for the normal leaf image. | S.Ramesh D.Vydeki | 2020 | Information Processing in Agriculture2020，7，2： | 2 |
| 6 | Al_2O_3-Sm_2O_3-CeO_2电解质的性能(英文)显示文摘采用溶胶-凝胶法和低温燃烧技术制备Ce1-xSmxO2(x=0,0.1,0.2,0.3)和掺杂Sm和(2%-8%)Al2O3的二氧化铈;研究其合成、结构、致密化、导电性和热膨胀等性能,并利用XRD研究其结构和相组成。结果表明,于1300°C烧结球团,获得致密的陶瓷,于1250°C在Ce0.8Sm0.2O0.2中加入2%和4%的Al2O3以促进烧结。利用扫描电子显微镜观察烧结后球团的表面形貌,使用双探针交流阻抗谱研究总离子电导率。 | S.RAMESH K.C.J.RAJU C.V.REDDY | 2012 | Transactions of Nonferrous Metals Society of China2012，22，6： | 1 |
| 7 | Closed-Form Solutions of Stress Intensity Factors for Semi-elliptical Surface Cracks in a Cylindrical Bar Under Pure Tension显示文摘In this work,the stress intensity factors(SIFs)for a wide range of semi-elliptical surface cracks with different inclination angles in a cylindrical bar subjected to pure tension were investigated numerically.The main parameters considered to evaluate the SIFs were the crack size ratio(a/d),the crack aspect ratio(a/c),and the crack inclination angle(0).The dual-boundary element met hod implemented in software BEASY was used to compute the SIF values for cracks.Furt her more,the general closed-form solutions were proposed to evaluate the corresponding SIFs for Mode I,Mode II and Mode III types of fracture through curve fitting approaches.These solutions can provide accurate and reliable values of stress intensity factors for a crack on a cylindrical bar under pure tension in a rapid way compared to those obtained using computational models.In addition,these results can be used as inputs for failure studies and life evaluations of cracked cylinder under working conditions. | M.K.Ramezani S.Ramesh J.Purbolaksono R.Das | 2022 | Acta Mechanica Solida Sinica2022，35，2： | 0 |
| 8 | Modelling of electric vehicle charging station and controlled by fuzzy logic controller with different modes of operation显示文摘The main objective of implementing charging stations is to ensure the good charging to theElectric Vehicles by using a solar PV array which is interconnected to the battery energy storagesystems. The charging station regulates the supply voltage and frequency without the use of amechanical speed governor. It also assures that energy gained from grid or by the DG set willhave the unity power factor (UPF) when the load is nonlinear. Besides this, the Point of CommonCoupling (PCC) voltage is synchronised with the grid/generator voltage in order to providecontinuous charging. In order to increase the optimal efficiency of the charging stations, thecharging stations will perform the active/reactive power transfer from the vehicle to grid, vehicleto house and vehicle to vehicle (V2V) power transfer. The operational experiment of the chargingstation is simulated and verified by using MATLAB/SIMULINK. | S.C.Vijay Kumar K.Karunanithi S.P.Raja S.Ramesh P.Chandrasekar R.Obulupathy | 2023 | Journal of Control and Decision2023，10，1： | 0 |
| 9 | Pattern Recognition of Modulation Signal Classification Using Deep Neural Networks显示文摘In recent times,pattern recognition of communication modulation signals has gained significant attention in several application areas such as military,civilian field,etc.It becomes essential to design a safe and robust feature extraction(FE)approach to efficiently identify the various signal modulation types in a complex platform.Several works have derived new techniques to extract the feature parameters namely instant features,fractal features,and so on.In addition,machine learning(ML)and deep learning(DL)approaches can be commonly employed for modulation signal classification.In this view,this paper designs pattern recognition of communication signal modulation using fractal features with deep neural networks(CSM-FFDNN).The goal of the CSM-FFDNN model is to classify the different types of digitally modulated signals.The proposed CSM-FFDNN model involves two major processes namely FE and classification.The proposed model uses Sevcik Fractal Dimension(SFD)technique to extract the fractal features from the digital modulated signals.Besides,the extracted features are fed into the DNN model for modulation signal classification.To improve the classification performance of the DNN model,a barnacles mating optimizer(BMO)is used for the hyperparameter tuning of the DNN model in such a way that the DNN performance can be raised.A wide range of simulations takes place to highlight the enhanced performance of the CSM-FFDNN model.The experimental outcomes pointed out the superior recognition rate of the CSM-FFDNN model over the recent state of art methods interms of different evaluation parameters. | D.Venugopal V.Mohan S.Ramesh S.Janupriya Sangsoon Lim Seifedine Kadry | 2022 | Computer Systems Science & Engineering2022，43，11： | 0 |
| 10 | Implementation of High-Q Embedded Band Pass Filter in Wireless Communication显示文摘At 12.8 MHz center frequency,the advanced miniaturized polymer-based planar high quality factor(Q)passive elements embedded bandpassfilter works in the L-band.Because most of the demands operate inside the spectrum,the wideband or high-speed operation necessary to enhance must be acquired in microwave frequency ranges.The channel has a quiet,high-performance micro-filter with wideband rejection.Capacitors and inductors are used in the high quality factor(Q)passive components,and related networks are incorporated in thefilter.Embedded layers are concatenated using Three-Dimensional Integrated Circuit(3D-IC)integration,parasitics are removed,and interconnection losses are negotiated using de-embedding methods.A wireless application-based Liquid Crystalline Polymer(LCP)viewpoint is employed as a substrate material in this work.The polymer processes,their properties,and the incorporated high-Q Band Pass Filter Framework.The suggestedfilter model is computed and manufactured utilizing the L-band frequency spectrum,decreasing total physical length by 31%while increasing bandwidth by 45%. | V.Satheesh Kumar S.Ramesh | 2023 | Intelligent Automation & Soft Computing2023，，5： | 0 |
| 11 | Hierarchically designed MoWSe_(2)/WO_(3)/C anode for fast and efficient Na+storage显示文摘Exploring anode materials with high energy and power density is one of the critical milestones in developing sodium-ion batteries/capacitors(SIBs/SICs).Here,the Mo and W-based bimetallic organic framework(Mo-W-MOF)with core-shell structure is first formed by a facile strategy,followed by a selenization and carbonization strategy to finally prepare multileveled Mo WSe_(2)/WO_(3)/C anode materials with core-shell petal like curled nanosheet structure.Between the petal(MoSe_(2))-core(WO_(3))structure,the formation of WSe_(2)flakes by partial selenization on the surface of WO_(3)serves as a heterogeneous connection between MoSe_(2)and WO_(3).The enlarged layer distance(0.677 nm)between MoSe_(2)and WSe_(2)can facilitate the rapid transfer of Na+and electrons.The density functional theory(DFT)calculations verify that the Mo WSe_(2)/WO_(3)/C heterostructure performs excellent metallic properties.Ex-situ X-ray diffraction(XRD),X-ray photoelectron spectroscopy(XPS),and transmission electron microscopy(TEM)confirm the activation process from the initial insertion reaction to the later conversion reaction.Resultantly,when employed as the anode of SIBs,a remarkable capacity of 384.3 mA h g-1after 950 cycles at 10 A g^(-1)is performed.Furthermore,the SICs assembled with commercial activated carbon(AC)as the cathode exhibits a remarkable energy density of 81.86 W h kg^(-1)(at 190 W kg^(-1))and 72.83 W h kg^(-1)(at 3800 W kg^(-1)).The unique structural design and the reaction investigation of the electrode process can provide a reference for the development of transition metal chalcogenides anodes. | Jian Wang Yachuan Shao Fei Yuan Huilan Sun Di Zhang Zhaojin Li S.Ramesh H.J.Woo Bo Wang | 2023 | Journal of Energy Chemistry2023，，5： | 0 |
您所在的机构暂未开通此部分的功能，请联系管理员