|
|
|
题名
|
作者
|
年代
|
出处
|
被引量
|
| 1 | Variation in Texture and Lankford Value of 1070 Aluminum Sheet Rolled by Cone-shaped Roll显示文摘A rolling with cone-shaped roll, the diameter of which continuously varies along the axial direction, has been proposed as a new shear rolling for controlling the texture of an aluminum alloy sheet. In this study, variations in the texture and Lankford value of a 1070 aluminum sheet rolled by the cone-shaped roll were investigated. Rolling with the cone-shaped roll was found to impose intense shear strain at the edges of the specimen, specifically near the surface. The shear directions in the left and right portions of the specimen were opposite to each other. The surface and middle layer of the specimen rolled by the cone-shaped roll and the reference specimen were characterized by a shear texture and typical recrystallization texture components, respectively. Notably, the specimen rolled by the cone-shaped roll exhibited smaller texture intensity than the reference specimen, especially at the surface, and the shear texture-components were observed at relatively deeper positions. As a result of Lankford value measurements, the specimen rolled with the cone-shape roll exhibited a smaller planar anisotropy than the reference specimen and an average Lankford value close to unity, which are likely due to the texture modifications introduced during rolling with the cone-shaped roll. | Yasumasa Chino Xinsheng Huang Kazutaka Suzuki Mamoru Mabuchi | 2013 | Journal of Materials Science & Technology2013，29，2： | 2 |
| 2 | Novel equilibrium two phase Mg alloy with the long-period ordered structure显示文摘 | Yasumasa Chino Mamoru Mabuchi Shigehiro Hagiwara Hajime Iwasaki Atsushi Yamamoto Harushige Tsubakino | 2004 | Scripta Materialia2004，，7： | 2 |
| 3 | Enhancementof tensile ductility of magnesium alloy produced by torsion extrusion显示文摘 | Yasumasa Chino Kensuke Sassa Mamoru Mabuchi | 2008 | Scr Mater2008，，59： | 1 |
| 4 | High-strain-rate superplasticity at low temperature in a ZK61 magnesium alloy produced by powder metallurgy 显示文摘 | Hiroyuki Watanabe Toshiji Mukai Mamoru Mabuchi et ol | 1999 | Scripta Materialia1999，41，2： | 1 |
| 5 | High-strainrate superplasticity at low temperature in a ZK61 magnesium alloy produced by powder metallurgy 显示文摘 | Watanabe H Mukai Toshi J Mabuchi Mamoru | 1999 | Scripta Materialia1999，41，6： | 1 |
| 6 | Highstrain-rate superplasticity at low temperature in a ZK61 magnesium alloy produced by powder metallurgy 显示文摘 | Hiroyuki Watanabe Toshiji Mukai Mamoru Mabuchi | 1999 | Scripta Materilia1999，41，： | 1 |
| 7 | High-strain-rate superplasticity at low temperature in a ZK61 magnesium alloy produced by powder metallurgy显示文摘 | Hiroyuki Watanabe Toshiji Mukai Mamoru Mabuchi | 1999 | Scripta Materilia1999，41，2： | 1 |
| 8 | Fabrication of nano-porous palladium by dealloying and its thermal coarsening显示文摘 | Masataka H Mamoru Mabuchi | 2009 | Journal of Alloys and Compounds2009，479，： | 1 |
| 9 | Mechanical anisotropy due to twinning in an extruded AZ31 Mg alloy显示文摘 | Yasumasa Chino Katsuya Kimura Masataka Hakamada Mamoru Mabuchi | 2007 | Materials Science & Engineering A2007，，1： | 1 |
| 10 | Deformation Characteristics at Room Temperature Under Biaxial Tensile Stress in Textured AZ31 Mg Alloy Sheets显示文摘 | Yasumasa Chino Katsuya Kimum Mamoru Mabuchi | | 0，，： | 1 |
| 11 | Influence of initial texture on cold deep drawability of Mg-3Al-1Zn alloy sheets显示文摘 | Xinsheng Huang Kazutaka Suzuki Yasumasa Chino Mamoru Mabuchi | 2012 | Materials Science & Engineering A2012，，： | 1 |
| 12 | Mechanical anisotropy due to twinning in an extruded AZ31 Mg alloy显示文摘 | Yasumasa Chino Katsuya Kimura Masataka Hakamada Mamoru Mabuchi | 2007 | Materials Science & Engineering A2007，，1： | 1 |
| 13 | Compressive deformation behavior at room temperature – 773K in Mg–0.2mass%(0.035at.%)Ce alloy显示文摘 | Yasumasa Chino Motohisa Kado Mamoru Mabuchi | 2007 | Acta Materialia2007，，3： | 1 |
| 14 | Novel equilibrium two phase Mg alloy with the long-period ordered structure 显示文摘 | Yasumasa Chino Mamoru Mabuchi Shigehiro Hagiwara | 2004 | Scr Mater2004，51，： | 1 |
| 15 | Influence of Zn concentration on stretch formability at room temperature of Mg–Zn–Ce alloy显示文摘 | Yasumasa Chino Xinsheng Huang Kazutaka Suzuki Kensuke Sassa Mamoru Mabuchi | 2010 | Materials Science & Engineering A2010，，2： | 1 |
| 16 | Microstructure and mechanical properties of a Mg-4Y-3RE alloy processed by thermo-mechanical treatment显示文摘 | TAKESHI Mohri MAMORU Mabuchi NAOBUMI Saito | 1998 | Materials Science and Engineering A1998，，257： | 1 |
| 17 | Microstructure and press formability of a cross-rolled magnesium alloy sheet显示文摘 | Yasumasa Chino Kensuke Sassa Akira Kamiya Mamoru Mabuchi | 2006 | Materials Letters2006，，7： | 1 |
| 18 | Compressive deformation behavior at room temperature – 773K in Mg–0.2mass%(0.035at.%)Ce alloy显示文摘 | Yasumasa Chino Motohisa Kado Mamoru Mabuchi | 2007 | Acta Materialia2007，，3： | 1 |
| 19 | Mechanical strength of nanoporous gold fabricated by dealloying 显示文摘 | Masataka Hakamada Mamoru Mabuchi | 2007 | Scripta Materialia2007，56，11： | 1 |
| 20 | Processing and mechanical properties of a porous low carbon steel with a controlled porous structure by imposition of a static magnetic field显示文摘 | Yasumasa Chino Mamoru Mabuchi Kensuke Sassa | 2006 | Mater Sci Eng2006，417，： | 1 |
您所在的机构暂未开通此部分的功能，请联系管理员